Troubleshooting - Bircher Reglomat ProLoop Betriebsanleitung

5 Simulation mode
The activation of the loops can only be simulated if loops are connected to the appropriate terminal!
The displays apply similarly for loop 2
Changeover to simulations mode Press «Sim1»
Changeover to simulation mode:
Press the Sim1 + Sim2 buttons
simultaneously for 2 seconds.
Simulation mode:
Activation of the loop with time
function
Activation of the loop without
time function
Alarm output activation
Inductance of loop 1
Inductance of loop 2
Exiting simulation mode
6

Troubleshooting

If an error occurs, operating mode «A» and error display «E» light up alternately and an error code such as E 012 is displayed. The LED changes to red,
the 4 most recent errors are stored and can be interrogated.
Display E001
Interruption
Error
Loop 1
7 Reset
Reset 1 (recalibration)
Mode
The loop(s) is/are recalibrated.
Sim1
2 seconds
Most important technical data
8
Supply voltage
Power consumption
Loop inductance
Loop connection wiring
Loop resistance
Output relay (loop)
Output relay (alarm)
Dimensions
Housing mounting
Connection type
Protection class
Approvals, safety
Operating temperature
Storage temperature
Air humidity
9 Declaration of conformity
Manufacturer: Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen declares that the
Product, type: ProLoop, ProLoop 11
Model: 24VDACDC, 115VAC, 230VAC, 1-loop devices, 2-loop devices
Intended purpose: Programmable loop detector for controlling gates and barriers as well as for regulating and counting cars in parking areas
if used in accordance with the intended purpose, complies with the basic requirements acc. to:
R&TTE Directive, Appendix III 1999/5/EC
Contact data
10
Manufacturer: Bircher Reglomat AG
Wiesengasse 20
CH-8222 Beringen
Switzerland
8
Press «Sim2»
button button
Mode
Sim1
2 seconds
2 seconds
Mode
1
Sim1
Mode
1
Sim1
Mode
Sim1
Mode
1
Sim1
Mode
2
Sim1
Mode
1 2
Sim1
2 seconds
E002 E011 E012
Interruption Short circuit Short circuit
Loop 2 Loop 1 Loop 2
Briefly pressing the «Data» button shows the last of 4 errors on the display. Another short press switches to the error before that,
and so on. When the button is pressed for the 5th time, the device switches back to automatic mode. If you press the «Data» button
for 2 seconds during the query, all error messages are deleted. The figure shows memory slot 1 in which error 001 Interruption loop
1 has been stored (example).
ProLoop
24 VAC –20 % to +10% 84 mA
24 VDC –10 % to +20% 84 mA
94–240 VAC ± 10%, 50/60 Hz,
23 to 12 mA
max. 2 VA
max. 40–1000 µH,
ideally 80–300 µH
max. 200 m 1,5 mm 2
min. 20x/m
< 8 Ohm with connection wire
240 VAC/2 A AC1
60 VAC, 0.3 A, AC1
22.5 x 94 x 88 mm (W x H x D)
Direct DIN rail mounting
Plug-in terminals
IP 30
See declaration of conformity at www.bircher-reglomat.com
–20°C to +60°C
–40°C to +70°C
<95% non-condensing
www.bircher-reglomat.com
info@bircher.com
Telefon +41 (0)52 687 1111
Telefax +41 (0)52 687 1112
Press «Sim2» Press «Sim2»
button button
Data
1
Sim2
Data
Data 1
2
Sim2 Sim2
Data Data
1 2
Sim2 Sim2
Data
Sim2
E101 E201
Under - EPROM
voltage Error
Mode
Data
Sim1
Sim2
8 seconds
ProLoop 11
24 VAC –20% to +10% 50 mA
24 VDC –10% to +20% 50 mA
115 VAC –15% to +10% 30 mA
230 VAC –15% to +10% 16 mA
24V 1.2 VA
max. 40–1000 µH,
ideally 80–300 µH
max. 200 m 1,5 mm
min. twisted 20x/m
< 8 Ohm with connection wire
240 VAC/2 A AC1
–
36 x 74 x 88 mm (W x H x D)
Mounting rail installation via 11-pin base BSF-11
Screw terminals base BSF-11
IP 20
See declaration of conformity at www.bircher-reglomat.com
–20°C to +60°C
–40°C to +70°C
<95% non-condensing
Notes
L0 -
L1 -
Activation of loop 1 with time function output 1
Data
2
Activation of loop 1 with time function output 2
Sim2
- Schleife 1 - Schleife 2
0 -
0
0 -
Activation of loop without time function output 1
Data
0
2
Sim2
Activation of loop without time function output 2
- Loop 1 - Loop2
A0
A1
-Switch off alarm relay
Switch on alarm relay
-
Measurement of the inductance, value in
Measurement of the inductance, value in
Return to function mode
E301 E302 E311
Loop 1 Loop 2 Loop 1
too large too large too small
Reset 2 (factory setting)
All values are reset to the factory settings (see Table 4.11a).
The loop(s) is/are recalibrated.
2
µH
µH
E312
Loop 2
too small