Werbung
- Insert the light bulb into the lamp projector so that it lies even to the bulging enclo-
sure. Make sure not to jam the wires of the light bulb.
- Secure the light bulb via the lamp ring. To this end the lamp ring must latch into the
enclosure groove of the point projector.
- Finally, re-attach the gear motor and test the correct device function.
9. Disposal
If the mirror ball set does no longer work and is beyond repair, dispose
of it according to the relevant statutory regulation.
10. Technical Data
Point projector Par 36
Voltage supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 V/ 50 Hz
Connected load: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 W
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000 g
Dimension (Ø x L): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 x 150 mm
Lighting agent: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6V 30 W Par 36
Colour wheel with motor
Voltage supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 V/ 50 Hz
Rotational speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.5 rpm
Colour wheel diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 mm
Colours: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .red, green, yellow, blue
Mirror ball motor
Voltage supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 V/ 50 Hz
Connected load: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 W
Max. supporting capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3000 g
Max. mirror ball diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 mm
Rotational speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5 rpm
Base plate diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 mm
Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 g
Mirror ball:
Diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 g
18
Do not replace damaged connection cables yourself. In this case you
should disconnect the devices from the mains and bring them to a
specialist workshop for repair.
In industrial facilities the safety regulations of the professional trade
association for electrical equipment and facilities must be observed.
If you assume that safe operation is no longer possible, put the device
out of service and protect it against unintentional operation.
Save operation is no longer given if the following factors apply:
•
the device show visible damage,
- the devices no longer work and
- after long storage under unfavourable conditions or
- heavy transport stress is likely.
Electrical equipment must be kept out of reach of children. Use
extreme caution when children are around. Children could try to stick
objects into the openings of the enclosure and suffer a lethal electric
shock.
Do not spill liquids over the devices. In this case immediate pull the
plug and contact a professional. There is the likely risk of fire or a lethal
electric shock. Make sure that the devices are sufficiently ventilated.
Do not cover or obstruct the ventilation slits. When setting up the
device provide for an appropriate ventilation.
Avoid strong mechanical stress, high temperatures, heavy vibrations
or excessive air humidity. This may damage the devices.
Never turn the product on immediately after it was brought from a cold
into a warm room. Condensation water that forms may destroy the
product under unfavourable conditions.
Leave the products switched off and wait until they have reached
room temperature and the condensation water has evaporated.
Do not leave packing material lie around unattended. Plastic
foils/bags, polystyrene parts can become dangerous for children.
If you are in doubt about the correct installation and commissioning or if you
have questions that this manual cannot solve, please contact your technical
hotline or other qualified personnel.
15
Werbung
Kapitel
