Operation; Care And Maintenance - Storch Crossline 360 Bedienungsanleitungen

Operation

1. Remove the battery compartment cover (pos. 3), insert four 1.5 V Alkaline batteries into the battery compartments
observing the + and - polarity signs; then reposition the battery compartment cover. Optionally connect the power sup-
ply included in delivery.
2. CrossLine 360 can be used as a standing device and is to be positioned onto a stable and vibration-free support. In
case of need and in case of levelling work at a determined height it can be mounted onto the corresponding holding
devices. (Optionally onto the tripod (item no. 441505) or at the wall bracket (item no. 441512)). If you use a tripod,
hold the centring nut on the device in one hand and turn the screw on the tripod into the centring nut on the device.
Tighten the screw. In case of using the wall bracket position the device onto the supporting arm and tighten from
below by means of the locking screw of the wall bracket.
3. Switch on the device (pos. 10): this switches on the power supply and the supporting laser diode bracket in the insi-
de of the housing is unlocked at the same time to allow for automatic self-levelling. (Switch off the device: the power
supply is switched off and the laser diode bracket is automatically locked).
4. Adjust the three levelling screws so that the spirit-level bubble in the base is in the black circle.
Please note: the spirit-level is only used as an aid for levelling the CrossLine 360. Levelling of the laser diodes is
effected internally and is independent of the spirit-level.
5. The laser diodes can be switched on via the control panel. The vertical lines can be activated individually by actua-
ting the "V-button": press 1 x - 1 vertical laser on, press 2 x – 2 vertical lasers on, forming an angle of 90 degrees, press
3 x – all 4 vertical lasers on. The 4 horizontal lasers switch simultaneously by actuation the "H-button". In case of need
you increase or decrease the luminosity of the laser diodes by means of the dimmer button "bulb icon".
6. Direct the vertical laser lines onto the provided position by turning the upper housing part of the device into the
desired position. Precisely adjust the vertical lines onto the desired position by means of the rotating fine adjustment
mechanism.
Please note: the fine adjustment mechanism is only used for fine adjustment of the targeted mark and not for a com-
plete 360 degree rotation.
7. If the laser beam flashes while the device is switched on, the angle of the device is too large; readjust the three
screws of the tripod / wall mount accordingly.
8. If the line laser angle exceeds the limit for some reason during operation, the laser beam will automatically start to
flash. In this case use the three levelling screws (in case of the tripod and wall mount mounting readjust the respective
holding device) to adjust the setting until the laser beam stops flashing. Possibly, reasons for setting changes can be
too strong vibrations or impacts in the installation area of CrossLine 360. In this case make sure that the malfunction
causes are eliminated.
9. Usage of the device after interruption of operation. By means of the plumbline beam projected by the device from
the bottom of the housing onto the ground it is possible for you to mark the installation position for being able to set up
the device subsequently on the same position. You will be able as well to mark the position of the vertical and horizon-
tal laser lines in order to be able to restore the last known position easier.

Care and maintenance

1. Never attempt to open the CrossLine. Only qualified STORCH service partners are allowed to repair the device.
2. To guarantee precision, protect the line laser against dropping, knocks and impacts.
3. When storing the device for an extended period of time, remove the batteries from the battery compartment.
4. Clean the device with a soft cloth and a mild detergent.
5. Never use aggressive chemicals, petroleum ether or cleaning agents, and do not keep the device in a dusty or hea-
vily contaminated environment.
6. Clean the red lenses with a spectacles cleaning cloth.
29