Inhaltsverzeichnis
Werbung
1.-
A
Velocità Snelheid Absaugleistung Ñêîðîñòü Velocidade Hastighet
Speed
Vitesse
Velocidad
I
Low
Moyenne
Baja
Bassa
II
High
Maximum
Alta
Alta
+
Intensive
Intensive
Intensiva
Intensa
Light
Lumière
Luz
Luce
On
Allumé
Encendido
Accesa
Off
Eteint
Apagado
Spenta
2.-
C
Íèçêàÿ
Laag
Leistungsstufe
Baixa
Âûñîêàÿ
Hoog
Intensivstufe
Alta
Èíòåíñèâíàÿ
Intensief
Intensiv
Intensiva
Licht
Beleuchtung
Îñâåùåíèå
Luz
Âêëþ÷åíî
Aan
Ein
Acesa
Îòêëþ÷åíî
Uit
Aus
Desligada
Instructions for use
By pushing buttons shown in the figure 1,
you will be able to control the functions of the
extractor
Two
achieve
better
recommend switching on the extractor a few
minutes before starting to cook (3 - 5
minutes) so that the air flow is continuous
and stable when extracting the fumes.
E
Likewise, keep the extractor switched on for
a few minutes when cooking is complete to
allow all fumes and odours to be expelled.
D
Cleaning and maintenance
Before
carrying
A
maintenance activities, ensure that the
extractor is disconnected from the mains.
B
To carry out cleaning and maintenance,
follow the Safety Instructions.
Filter cleaning
To remove the filters from their locations
release the anchoring points. Clean the filter,
Låg
either by putting it in the dishwasher (see
Hög
notes) or leaving it standing in hot water to
simplify the removal of grease or, if wished,
Intensiv
by means of special sprays (protecting the
Lampa
non metallic parts). Once clean, leave it to
På
dry.
Av
Notes: cleaning in the dishwasher with
aggressive detergents may darken the
surface of
metallic
affecting its gas retaining properties.
N.B. The filter must be cleaned at least once
a month depending on how often the
extractor is used. It must be remembered
that grease accumulates in the extractor
when cooking, whether it is switched on or
not.
Cleaning of the extractor body
The use of warm (40ºC approx.) soapy water
is recommended. A cloth moistened in this
water is used for cleaning the extractor,
paying
special
attention
Afterwards, dry it using a lint-free cloth.
Note:
* Never use metallic scouring pads or
abrasive products that could damage the
surface.
* Do not use scrapers with metallic surfaces
such as knives, scissors etc.
extraction,
we
Active charcoal filter
* To install the charcoal filters it is necessary
to firstly remove the metallic grease filters.
* In order to fix them it is necessary to
introduce the rear lips of each filter in the
holes provided for it in the security grid,
turning them upwards until its fixation by
clipping in the front part (Fig.6).
* The carbon filters last from three to six
months
conditions of use.
out
any
cleaning
or
* The active carbon filters can neither be
washed nor regenerated. Once they are
exhausted, they must be changed.
* To replace worn out filters with new ones,
remove the old ones in the reverse order to
that of installation
Changing Bulbs
* It is important that the mains are
disconnected, and ensure the bulbs that are
to be replaced are not hot.
* Remove the light lens to expose the
extractable lamps.
* The maximum bulbs power is 20W.
Technical Information
Dimensions
parts, without
this
Electrical characteristics:
REFER TO RATING PLATE
to
the
grids.
depending
on
the
particular
.
(Fig.3)
Width = 600//900 mm
Depth = 300 mm
Height = 353 mm
Werbung
Inhaltsverzeichnis
