Herunterladen Inhalt Inhalt Diese Seite drucken

Sicherheitsvorkehrungen; Safety Warning; Maintenance - Vitavia URANUS 6700 Montageanleitung

Vorschau ausblenden Andere Handbücher für URANUS 6700:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

1. PLEASE READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE ASSEMBLING YOUR GREENHOUSE.
2. Sharp edges and corners can cause injury. Always wear protective glasses, gloves, shoes and headgear when handling the aluminium profiles, glass and
polycarbonate sheets. Broken glass is a safety hazard – always clear up immediately and dispose of with care.
3. The product you have purchased is intended only for the growing of plants and should only be used for this purpose. When used for other purposes we
will take no responsibility.
4. It is recommended that this greenhouse is assembled by two people.
5. Should you encounter difficulties constructing this house, or in fitting the glass or polycarbonate sheets, please contact your retailer
– do not use force!
SITE SELECTION
Always try to select a sunny location, sheltered
from the wind as much as possible.
IMPORTANT
Before assembling your new greenhouse,
please check that all parts in the provided list
are included. Please take each bundle out of
the packaging in order to identify the parts
better.
It is important that the opened bundles do not
get mixed with one another.
If something is missing please contact your
retailer.
NECESSARY TOOLS
Screw drivers (Normal and Crosshead),
10 mm spanner or wrench.

MAINTENANCE

The greenhouse should be thoroughly washed
with a gentle detergent occasionally. Please
check that the detergent used does not react
aggressively with aluminium or the glass fixing
clips.
Ensure that the upper and lower door tracks
are cleaned regularly to avoid a build up of
debris.
0 BASE
Important! The base must be exactly square
and level. A zinc-coated steel base is available
as an accessory for all greenhouse models.
(Attention! Only when the greenhouse must
be located in a very windy and unprotected
location: Drill through both the profile at the
base of the greenhouse and the steel base,
and connect them with nuts and bolts.)
6

SICHERHEITSVORKEHRUNGEN

Safety Warning

Assembly Instructions
If you would rather construct your own stone
or concrete foundation, please follow the
dimensions specified in diagram 0. Treated
wooden beams at least 18 mm high and not
more then 32 mm wide should be positioned
between the stone/concrete foundation and
the aluminium frame, and connected to the
foundation with 50 mm long bolts (not pro-
vided).
All diagrams are shown from the inside
of the house, with the exception of those
enclosed in a double frame, indicating the
outside view.
1. SIDE ELEMENTS
Lay all of the parts on the floor and connect
them loosely.
At this stage it is necessary with each vertical
aluminium bar (2055) to include an extra
connecting bolt, to later connect corner braces
(1056) (1.5). On the outside bars (2055) in-
clude one additional extra bolt, to also connect
cross braces (2095) (1.2).
Loosely connect the corner plate (1092) (1.1).
In step 4 the corner plate bolts must also be
connected to the gabel ends.
2. PLAIN GABEL END
Lay all of the parts on the floor and connect
them loosely.
Include two extra connecting bolts in the
vertical bars (2041 and 2042) to connect the
cross braces (2.2) and (2.6). In the vertical bar
(2101) please include only one extra bolt.
3. DOOR GABEL END
Lay all of the parts on the floor and connect
them loosely.
The door runner bars (1047) will be connected
to the horizontal bar (2048). Connect these
loosely from the outside with two nuts and
bolts.
Connect the clips (1013) as shown in (3.8)
with a bolt, in order to strengthen the structure.
Please control that the clip edge overlaps, and
fixes the vertical bars (2044) or (2045) as
shown.
As in step 2, please include two extra bolts in
both vertical bars (2044) and (2045).
4A. CONNECTING THE SEPARATE
ELEMENTS
Bolt the side elements to the end elements.
(4.1) & (4.2).
Loosely connect the corner plate (1092) above
the eaves (4.3).
Assemble the ridge bar and then the corner
plates (1092) on the gabel ends (4.4).
Connect the door runner supports (2043) to
the door runner bars (1047) and to the gabel
end, using bolt (1005) and spacer (1010) (4.5).
4B. CONNECTING THE SEPARATE
ELEMENTS
Connect the roof glazing bars (2055) between
the eaves (4.6) and the roof ridge (4.7). Insert
extra bolts into each glazing bar depending on
which house you have bought. The number is
indicated in a circle on each bar and to be
read beginning from both ends.
The corner braces (1056) (4.6), the upper
corner braces (2057) (4.8) and the cross
braces (2033) (4.10) can now be connected.
Now position your greenhouse on the pre-
pared base/foundation and connect loosely.
Adjust the greenhouse until it is completely
square and tighten all bolts.
Please do not over tighten.
001.01.0802

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Uranus 8300Uranus 9900Uranus 11500

Inhaltsverzeichnis