Maxi-Cosi Mobi Bedienungsanleitung Seite 5

EN
• Place the Mobi (XP) in the sleeping position (see section 3.2: Seat positions)
IMPORTANT!
• Make sure the support leg is in the folded-out position to enable you to access the back
of the Mobi (XP) (see Step 5; Positioning the support leg).
• Pull the shoulder belts until the belt yoke on the back appears and remove the shoulder belts from the
5
belt yoke (5).
IMPORTANT!
• Make sure the belt buckle is locked in order to prevent the belts from twisting.
• Pull the shoulder belts out of the belt pads through the shell and cover. Do this on both sides (6).
6
• TIP! Loosen the top part of the cover to make it easier to remove the belts and belt pads. Remember to
7
reattach the cover to the shell afterwards (7).
• Remove the belt pads (8).
8
• From the front, thread one belt pad through the correct slot in the cover and shell and then rethread this
9
belt pad through the back through the adjacent slot (9).
IMPORTANT!
• Make sure the strap between the belt pads lies tight against the plastic shell and does
not become entangled with the belt portion of the support leg.
Mobi
• Thread the shoulder belts through the adjusted belt pads, cover and shell (10).
Semibold Italic 36 pt
10
Mobi XP
• Attach the shoulder belts to the belt yoke and check to make sure the 3 red stitching on the belt ends
11
and the belt yoke are facing the shell (11) (if not, this means the belts are twisted).
IMPORTANT!
• Make sure the belts are threaded along the plastic shell, remain behind the rods and do
12
Mobi
not become entangled with and stay behind the belt portion of the support leg (12).
Semibold Italic 36 pt
Mobi XP
Mobi
Adjusting the height of the shoulder belts
Semibold 36 pt
Mobi XP
The correct belt height of the shoulder belts is attained when the belt disappears into the shell slightly
XP1
above theshoulder of the child. Make sure that the shoulder belts fit properly over the shoulders of the
child (XP1).
• Loosen the shoulder belts by pressing the release button and pulling the shoulder belts towards you as
01
far aspossible (01) Important: Do not pull the belt pads when doing so.
• Lift up the flap on the cover by the shoulder belt slots (XP2).
XP2
• To make the adjustment easier, pull the shoulder belts on top of the belt pad forward into a loop,
XP3
loosening them (XP3).
• Next, push the loop back through the opening (XP4).
XP4
• Slide the shoulder belt and the belt pad strap through the slot together into the next position (XP5).
XP5
Make sure that theshoulder belt is positioned on top of the belt pad strap in the new position (XP6).
XP6
Always do this on both sides.
• Pull the shoulder belts tight by pulling on the belts under the belt pads (XP6).
XP6
• Place the flap back in position and thread the belt pads through the correct slots in the flap and secure
XP7
them with theVelcro (XP7).
• Check whether you are able to use the belts and ensure they are not twisted.
Step 2: Checking for anchor points or installing the car kit
Remove the elastic band from around the tethers and let the tethers drop to the floor. There are three
ways to hook the tethers onto the anchor points in the car. Specific anchor points may already be present
in the car that can be used. If not, the car kit components or metal attachment hooks provided can serve
as anchor points. Whenever possible, use the most forward positioned anchor points to attach the
tethers.
Anchor points already present in the car
• Check the passenger seat rails for anchor points.
13 14
In some cars, the child seat anchor points are part of the rail itself (13). In others, there are metal child
seat anchor loops bolted to the rail, often painted blue (14).
• Check whether the hooks of the tether can be easily connected to and disconnected from the present
15
anchor points (15). If so, use these points to anchor the Mobi (XP).
IMPORTANT!
• Make sure the straps of the tethers are not twisted.
• Wait with tightening the tethers until after Step 4; Positioning the support leg.
• Wherever possible, use the most forwarded positioned attachment points for the tethers.
10
Extra anchor points provided with the Mobi (XP)
The Mobi (XP) has extra anchor points that you can use to tether the Mobi (XP) if no anchor points are
available in your car. There are several options for doing this.
Study the bottom of the car seat and the seat rails and choose the right configuration for installation; car
kit or metal attachment hooks (both included).
a) Car kit
The (below) chart shows all possible configurations for installing the car kit components.
To obtain the right length, a suitable opening in the tether must be chosen (16).
16
IMPORTANT!
• Determine the length based on the position of the Mobi (XP) in the car (rear, middle or
front seat).
• Simply hook the tether hook onto the anchor point (17).
17
IMPORTANT!
• Make sure the tether straps and car kit components are not twisted.
• Wait with tighten ing the tethers until after Step 4; Positioning the support leg.
Car kit
components
1
braided together
as single
component
2
3
Car kit
2x
components
1
attached
separately
2
3
b) Metal attachment hooks
If you can see a bolt holding down the seat rail you can use the metal attachment hooks as separate
anchor loops.
• Ask your car dealer to connect the metal attachment hooks to the bolt (18).
18
IMPORTANT!
• Ask your certified car dealer to connect the metal attachment hooks. Changes to the car
done by yourself can affect the warranty conditions of your car.
• Simply hook the tether hook onto the metal attachment hooks (19).
19
IMPORTANT!
• Make sure the tether straps are not twisted.
• Wait with tightening the tethers until after Step 4; Positioning the support leg.
EN
Mobi on
Mobi on Mobi on
FRONT SEAT MIDDLE SEAT REAR LEFT/
RIGHT SEAT
11