Seite 1
® Oxford Oxford Presence ® User Instruction Manual & Warranty To avoid injury, read user manual prior to use. Oxford Presence ® Manuel de l’utilisateur et garantie Afin d’éviter tout accident, veuillez lire attentivement la notice avant utilisation. Oxford Presence ®...
Oxford ® E n g l i s h Presence 1. The Oxford Presence Patient Lift Boom Battery/ Control Pack Push Handle Spreader Bar Electric Actuator Mast Extrusion Rear Castor (braked) Front Castor (non-braked) 294000.10007 Rev. D...
Presence 2. Introduction: About Your Lift The Oxford Presence is an electrically operated patient lift. Each Presence lift is fully assembled load tested and certified before being packed/shipped. The packing consists of a strong, purpose built carton that is used for both export and domestic markets to ensure the safe arrival of the lift.
DESK TOP CHARGER/STAND • WARNING The Oxford Presence is heavy and will need to be lifted with care. You may need assistance to lift the Oxford Presence from the carton. ASSEMBLY INSTRUCTIONS Remove all the parts from the carton and place on the floor, taking care to protect the finish from damage.
Seite 6
Oxford ® E n g l i s h Presence Tighten the mast assembly with the mast-locking device, which is located at the front of the chassis. WARNING Avoid trapping fingers. Keep fingers away from the end of the mast when inserting into the chassis socket.
Seite 7
Oxford ® E n g l i s h Presence DISASSEMBLY The lift should not be disassembled unless for service, repair or transport if necessary. Therefore follow the assembly instructions in reverse sequence. ALWAYS CHECK THE FOLLOWING BEFORE OPERATION • The mast is fully locked into position.
Seite 8
Oxford ® E n g l i s h Presence • Push the up and down buttons on the hand control and confirm the boom rises and lowers. 294000.10007 Rev. D...
E n g l i s h Presence 4. Safety Precautions Please read and follow the safety precautions listed below. The operation and use of Oxford patient lifts is simple and straightforward. Following these few basic safety precautions will make lifting operations easy and trouble free.
Seite 10
Oxford ® E n g l i s h Presence • The MINIMUM load required to manually lower the hoist using the mechanical emergency down function is 30 kg. • DO NOT park a loaded lift on ANY sloping surface.
Battery Indicator 1. Leg adjustment The legs on the Oxford Presence are electrically adjustable for width. The legs can be opened to enable access around armchairs or wheelchairs. For transferring and negotiating narrow doorways and passages the lift legs should be in the closed position.
Seite 12
Complete the lifting operation and place the battery on charge (see charging instructions). 8. Slings The Oxford Presence has the option of both a 6-point spreader bar and a 4-point positioning cradle. Both systems use different attachment methods and slings.
Seite 13
Oxford ® E n g l i s h Presence The four point cradle sling attaches to the cradle studs via a safety clip system (shown below), each sling is supplied with instructions. Please study the instruction guide before use...
E n g l i s h Presence OXFORD RECOMMENDS THE USE OF GENUINE OXFORD PARTS. Oxford sling and lift prod- ucts are designed to be compatible with one another. For country specifi c guidance on sling use and compatibility, please refer to the sling label or contact your local market distributor or Joerns Healthcare.
Seite 15
Oxford ® E n g l i s h Presence FOLLOW THESE INSTRUCTIONS EXACTLY Your presence lift has the option of using both a 6-point spreader bar and 4-point positioning cradle. The removal of either of these systems is completed easily by the use of a quick-release pin.
Seite 16
Oxford ® E n g l i s h Presence 294000.10007 Rev. D...
Seite 17
Oxford ® E n g l i s h Presence REMOVAL CAUTION: Be sure to support the weight of the spreader bar/cradle before removing pin. Removable Battery Pack Hand Control Legs Open/Close, Boom Raise/Lower Control Box Emergency Stop, Raise/Lower To detach pin, depress the spring barb (using a flat blade electrical screw driver or similar) and pull the pin out.
Seite 18
Oxford ® E n g l i s h Presence 294000.10007 Rev. D...
Fit the power pack to the lift and make sure the latch holding the pack in place is fully engaged. “Click” in place. The charging of Oxford electric lifts is simple and straightforward, but it is important to follow the charging instructions closely. Please pay particular attention to the following points, they will help you avoid problems with discharged batteries.
Seite 20
Oxford ® E n g l i s h Presence *THESE CHECKS SHOULD INCLUDE: 1. SPREADER BAR: Check the spreader bar for freedom of rotation and swing. Check for wear on the central pivot. Check for firm attachment to ...
Seite 21
Oxford ® E n g l i s h Presence WARNING KEEP the batteries fully charged. Place the battery on charge whenever it is not in use. If it is more convenient to do so, place on charge every night. The charger will not allow the batteries to overcharge.
DO NOT use, and place on charge immediately. MAINTENANCE, INSPECTION AND TEST Joerns Healthcare recommend a thorough inspection and test of the Oxford Presence lift and lifting accessories, slings, scales etc is carried out on a regular basis. Inspection frequency varies depending on locality, so you must check with your dealer or local government agency as appropriate regarding how often an inspection is required.
Oxford ® E n g l i s h Presence 9. Technical Specifications Safe Working Load ............500 lbs 227 kgs Maximum Overall Length ..........57.5 inches 1460 mm Minimum Overall Length ..........55.1 inches 1400 mm Maximum Overall Height ..........81.3 inches 2065 mm Minimum Overall Height ..........57.5 inches...
Tel: 0844 811 1156 • Fax: 0844 811 1157 info@joerns.co.uk • www.joerns.co.uk Table des matières 1. Lève-personne Oxford Presence..............25 2. Introduction: À propos de votre lève-personne ..........26 3. Instructions de montage et de mise en service ..........27 4. Consignes de sécurité ................31 5.
Oxford ® F r a n ç a i s Presence 1. Lève-personne Oxford Presence Flèche Bloc de commande de la batterie Poignée de manœuvre Barre d’écartement Actionneur électrique Partie extrudée du mât Roulette arrière (avec frein enclenché) Rouletter avant (sans frein enclenché)
• Oxford Quickfit Deluxe • Oxford Silkfit • Oxford Long Seat Marque CE : L’appareil Oxford Presence porte la marque CE et il est conforme aux directives CE suivantes : • Medical Device Directive (appareils médicaux) (93/42/EEC) • Directive EMC (89/336/EEC) •...
AVERTISSEMENT L’appareil Oxford Presence est lourd et doit être soulevé avec précaution. Vous aurez éventuellement besoin d’aide pour soulever l’appareil Oxford Presence et le sortir de sa boîte. MONTAGE Retirez toutes les pièces de la boîte et placez-les par terre, en prenant soin de protéger le fini.
Seite 28
Oxford ® F r a n ç a i s Presence Resserrez le mât à l’aide du dispositif de verrouillage du mât situé devant le châssis. AVERTISSEMENT Évitez de coincer vos doigts. Lorsque vous insérez le mât dans la fente, gardez vos doigts à...
Seite 29
Oxford ® F r a n ç a i s Presence EFFECTUEZ TOUJOURS LES VÉRIFICATIONS SUIVANTES AVANT D’UTILISER L’APPAREIL: • Le mât est complètement verrouillé en position • Les pieds du lève-personne s’ouvrent et se referment de façon satisfaisante (Pour cela, utilisez la commande manuelle).
Seite 30
Oxford ® F r a n ç a i s Presence • Appuyez sur les boutons « up » (vers le haut) et « down » (vers le bas) de la commande manuelle pour confirmer que la flèche se lève et s’abaisse.
Veuillez lire et suivre les consignes de sécurité ci-dessous. Le fonctionnement et l’utilisation des lève-personnes Oxford sont simples et clairs. Si vous suivez ces quelques consignes de sécurité fondamentales, vous serez en mesure d’utiliser ce lève-personne facilement et sans problème.
Seite 32
Oxford ® F r a n ç a i s Presence • NE poussez PAS le lève-personne sur un terrain accidenté particulièrement s’il est chargé. • N’essayez PAS de pousser / tirer un lève-personne chargé pour surmonter un obstacle au sol.
1. Réglage des pieds La largeur des pieds de l’appareil Oxford Presence est réglable. Les pieds peuvent être ouverts pour faciliter l’accès autour des fauteuils ou des chaises roulantes. Pour permettre les transferts et le passage par des portes et des endroits exigus, les pieds du lève-personne doivent être en position fermée.
Seite 34
NÉGLIGEZ PAS CETTE ALARME. Achevez le levage et mettez l’appareil sous charge (voir instructions de charge). 8. Courroies L’appareil Oxford Presence peut être équipé d’une barre d’écartement à six points ou d’une chassis à quatre points de fixation. Les deux systèmes utilisent des méthodes de fixation et des courroies différentes.
Seite 35
Oxford ® F r a n ç a i s Presence Sangles Points d’attache de la sangle d’épaule de retenue de la jambe Points d’attache de la sangle d’épaule Sangles de retenue de jambe Barre d’écartement à 6-points; Exemple d’une courroie pour barre d’écartement à six points munie d’attaches en boucle.
Seite 36
AVERTISSEMENT OXFORD RECOMMANDE L’UTILISATION DE PIECES OXFORD AUTHENTIQUES. Les produits de sangle et de levage Oxford sont conçus pour être compatibles ensemble. Pour les directives spécifi ques à votre pays au sujet de l’utilisation d’élingues et de leur compatibilité, veuillez lire l’étiquette de l’élingue ou contacter votre revendeur local ou Joerns Healthcare.
Oxford ® F r a n ç a i s Presence 6. Dépose des systèmes de barres d’écartement/chassis à 4-points de fixation SUIVEZ CES INSTRUCTIONS À LA LETTRE Votre lève-personne Presence a l’option d’un système d’écartement à 6-points ou chassis à...
Seite 38
Oxford ® F r a n ç a i s Presence DÉPOSE ATTENTION: Vérifiez que le poids de la barre est correctement/chassis supporté avant de retirer la goupille. Pour détacher la broche, appuyez sur la languette de ressort (à l’aide d’un tournevis plat ou un outil similaire) et extrayez la broche.
Enclenchez le bloc. Le chargement des lève-personnes électriques Oxford est simple et clair, mais vous devez absolument suivre les instructions à la lettre. Prêtez une attention toute particulière aux points suivants, vous évit- erez ainsi de vous retrouver avec des batteries déchargées.
Seite 40
Oxford ® F r a n ç a i s Presence AVERTISSEMENT GARDEZ les batteries complètement chargées. Mettez le lève-personne sous charge lorsqu’il n’est pas en usage. Si cela est plus pratique, chargez-le chaque nuit. Le chargeur ne « surchargera » pas les batteries.
8. Périodicité d’entreien et liste des vérifications quotidiennes Tous les produits Oxford sont conçus de manière à ne nécessiter qu’un entretien minimal; toutefois, certaines vérifications et procédures de sécurité sont nécessaires. Un tableau des tâches QUOTIDIENNES est présenté ci-après. Des vérifications quotidiennes et un entretien, une inspection et un essai semestriel garantissent que le lève-personne fonctionne parfaitement.
Seite 42
Oxford ® F r a n ç a i s Presence *CES VÉRIFICATIONS DOIVENT PORTER SUR: 1. BARRE D’ÉCARTEMENT: Vérifiez que la barre d’écartement tourne et pivote librement. Vérifiez l’absence d’usure sur le pivot central. Assurez-vous qu’elle est solidement fixée sur la flèche.
Oxford ® F r a n ç a i s Presence 9. Spécifications techniques Charge maximale d’utilisation ........500 lbs 227 kgs Longueur maximale hors tout .........57,5 pouces 1460 mm Longueur minimale hors tout ..........55,1 pouces 1400 mm Hauteur maximale hors tout ...........81,3 pouces 2065 mm Hauteur minimale hors tout ..........57,5 pouces...
Oxford ® F r a n ç a i s Presence SPÉCIFICATIONS ÉLECTRIQUES BATTERIES ............12 volts, type plomb-acide, scellées rechargeables CAPACITÉ DES BATTERIES ......3,2 A / h VALEURS NOMINALES D’ENTRÉE DU CHARGEUR ....230 Vca, 50 / 60 Hz VALEURS NOMINALES DE SORTIE DU CHARGEUR ...27,4 / 29,0 Vcc à...
Oxford ® F r a n ç a i s Presence 10. Garantie Joerns Healthcare dispose d’un réseau établi de distributeurs et revendeurs réputés qui se feront un plaisir de répondre à toutes vos questions concernant l’achat, la garantie, les réparations et l’entretien.
Oxford ® D e u t s c h Presence 1. Oxford Presence Patientenlifter Ausleger Steuerungseinheit des Akkusatzes Schiebejandgriff Spreizbügel Elektrischer Stellmotor Mastspitze Hintere Laufrolle (feststellbar) Vordere Laufrolle (nicht feststellbar) 294000.10007 Rev. D...
D e u t s c h Presence 2. Einführung: Über Den Lifter Der Oxford Presence ist ein elektrisch betriebener Patientenlifter. Der Presence-Lifter wird vor der Auslieferung vollständig montiert, unter Last getestet und zertifiziert. Die Verpackung besteht aus einem festen, zweckmäßig geformten Versandkarton für den sicheren Transport des Lifters und wird sowohl für den heimischen Markt als auch für den Export...
• LADEKABEL • TISCHLADEGERÄT/STÄNDER WARNUNG Der Oxford Presence ist schwer und muss vorsichtig gehoben werden. Holen Sie sich Hilfe, um den Oxford Presence aus dem Karton zu heben. MONTAGE Nehmen Sie alle Teile aus dem Karton heraus, legen Sie sie auf den Boden und achten Sie darauf, dass die Oberfläche des Geräts nicht beschädigt wird.
Seite 50
Oxford ® D e u t s c h Presence Ziehen Sie den Mast mit dem Mast-Feststellknopf fest, der sich vorne am Rahmen befindet. WARNUNG Quetschgefahr: Halten Sie die Finger vom Mastende fern, wenn Sie den Mast in die Rahmenbuchse einsetzen. Das Etikett auf der Mastseite zeigt an, wann der Mast vollständig eingesetzt ist.
Seite 51
Oxford ® D e u t s c h Presence DEMONTAGE Der Lifter sollte nur bei Bedarf für Wartung, Reparatur oder Transport demontiert werden. Hierzu befolgen Sie die Montageanweisungen in umgekehrter Reihenfolge. PRÜFEN SIE VOR DEM BETRIEB STETS DIE FOLGENDEN PUNKTE: •...
Seite 52
Oxford ® D e u t s c h Presence • Drücken Sie die Aufwärts- und Abwärts-Tasten auf der Handbedienung und vergewissern Sie sich, dass sich der Ausleger hebt und senkt. 294000.10007 Rev. D...
4. Sicherheitshinweise Lesen und befolgen Sie die nachfolgend aufgeführten Sicherheitshinweise. Betrieb und Funktionsweise des Oxford Patientenlifters sind einfach und direkt. Wenn Sie diese grundleg- enden Sicherheitsvorkehrungen beachten, ist der Hebebetrieb leicht und problemlos. DER „PRESENCE“ LIFTER DARF NUR VON PERSONEN VERWENDET WERDEN, DIE DIESES BENUTZERHANDBUCH GELESEN UND VERSTANDEN HABEN.
Seite 54
Oxford ® D e u t s c h Presence • Schieben/ziehen Sie den beladenen Lifter NICHT über Hindernisse am Boden. • Betätigen Sie die Bedienungs-/Sicherheitselemente NIEMALS mit Gewalt. Alle Elemente sind leichtgängig und ohne größere Kraftanstrengung zu betätigen. • Die MINDESTLAST zum manuellen Absenken des Patientenlifters mit der mechanischen Notabsenkung beträgt 30 kg.
Akkuanzeige Stellmotor 1. Einstellen der Fahrgestellbreite Die Breite des Fahrgestells am Oxford Presence ist elektrisch einstellbar. Das Fahrgestell kann gespreizt werden, um Sessel oder Rollstühle zu umschließen. Für den Transfer durch enge Türen und Durchgänge sollte das Fahrgestell zusammengeführt werden.
Seite 56
Akkus auf (siehe „Aufladen der Akkueinheit“). 8. Gurte Der Oxford Presence bietet die Wahl zwischen einem Sechspunkt- Spreizbügel und einem Vierpunkt- Rahmen. Diese beiden Systeme verwenden verschiedene Befestigungsmethoden und Gurte. Das Sechspunktsystem verwendet Gurte mit Gurtschlingen, die ein Einstellen der Position durch die Auswahl verschiedenfarbiger Schlingen ermöglichen.
Seite 57
Oxford ® D e u t s c h Presence Das Vierpunkt-Rahmengurt wird an den Ständer des Hebebügels mit einem Sicherheitsclipsystem befestigt (siehe unten). Für jeden Gurt werden spezielle Anweisungen mitgeliefert. Lesen Sie bitte vor Gebrauch die Anweisungen. Schulterriemen Befestigungspunkte für Beinriemen...
Seite 58
WARNUNG OXFORD EMPFIEHLT DIE VERWENDUNG VON ORIGINAL OXFORD-TEILEN. Bespannungen und Lifts von Oxford sind frei miteinander kombinierbar. Länderspezifi sche Angaben zur Bespannung und Kompatibilität fi nden Sie im Etikett der Bespannung oder wenden Sie sich an Ihren örtlichen Händler oder an Joerns Healthcare.
Oxford ® D e u t s c h Presence 6. Entfernen der Sechspunkt-Spreizbügelsysteme und Vierpunkt-Rahmen DIESE ANWEISUNGEN BITTE GENAU BEFOLGEN Ihr Presence-Patientenlifter kann sowohl mit einem Sechspunkt- wie auch einem Vierpunkt-system verwendet weerden. Diese Systeme lassen sich mit Hilfe eines Schnellauslösestifts leicht entfernen.
Seite 60
Oxford ® D e u t s c h Presence ENTFERNEN VORSICHT: Stellen Sie sicher, dass Sie das Gewicht der Querstange stützen/Rahmen, bevor Sie den Stift entfernen. Um den Stift zu entfernen, die Steckfeder (mit Hilfe eines Flachschraubenziehers oder eines ähnlichen Werkzeugs) eindrücken und den Stift herausziehen.
Verschluss, der die Einheit an ihrem Platz hält, vollständig eingerastet ist. Die Einheit muss mit einem klickenden Geräusch einrasten. Das Aufladen elektrischer Oxford Lifter ist einfach und direkt, aber es ist wichtig, die Ladeanweisungen genau zu befolgen. Beachten Sie bitte die folgenden Punkte, die Ihnen dabei helfen, Probleme mit entladenen Akkus zu vermeiden.
Seite 62
Oxford ® D e u t s c h Presence WARNUNG Die Akkueinheit STETS voll aufladen. Lassen Sie die Akkueinheit immer aufladen, wenn sie nicht benutzt wird. Wenn es für Sie praktischer ist, laden Sie sie jede Nacht auf. Das Ladegerät schützt die Akkueinheit vor Überladen.
Presence 8. Wartungsplan und Tägliche Prüfliste Alle Oxford Produkte sind so konzipiert, dass sie nur ein Minimum an Wartung benötigen. Einige Sicherheitsprüfungen und -prozeduren sind jedoch unerlässlich. Im Folgenden sind die TÄGLICH auszuführenden Aufgaben aufgeführt. Tägliche Überprüfungen und alle sechs Monate Wartung, Inspektion und Prüfung gewährleisten, dass ein Lifter in optimalem, sicherem Funktionszustand...
Oxford ® D e u t s c h Presence *DIESE PRÜFUNGEN SOLLTEN UMFASSEN: 1. SPREIZBÜGEL: Vergewissern Sie sich, dass der Spreizbügel frei dreh- und schwenkbar ist. Prüfen Sie den zentralen Stift auf Verschleiß. Prüfen Sie, dass der Stift fest mit dem Ausleger verbunden ist.
Oxford ® D e u t s c h Presence 9. Technische Daten Zulässige Belastung ............500 lbs 227 kgs Maximale Gesamtlänge ..........57,5 Zoll 1460 mm Minimale Gesamtlänge ........... 55,1 Zoll 1400 mm Maximale Gesamthöhe ..........81,3 Zoll 2065 mm Minimale Gesamthöhe ...........
Oxford ® D e u t s c h Presence ELEKTRISCHE DATEN AKKUS: ................12 V, wiederaufladbar, geschlossene Blei/Säure-Akkus AKKUKAPAZITÄT: ............3,2 Ah EINGANGSSPANNUNG DES LADEGERÄTS (NENNWERT): ..230 V Wechselstrom, 50/60 Hz AUSGANGSSPANNUNG DES LADEGERÄTS (NENNWERT): ..27,4/ 29,0 V Gleichspannung bei 0,8 A ÜBERSPANNUNGSSCHUTZ...
Oxford ® D e u t s c h Presence 10. Prüfung Joerns Healthcare verfügt über ein Netzwerk von renommierten Vertriebspartnern und Händlern, die Ihre Kauf-, Garantie-, Reparatur- und Wartungsanfragen gerne bearbeiten. Wir gewähren eine Produktgarantie von 24 Monaten ab Herstellungsdatum oder 24 Monate ab Verkaufsdatum, sofern das Produkt über einen autorisierten Händler bestellt worden ist.
Seite 68
WR10 2AG United Kingdom Tel: 0844 811 1156 • Fax: 0844 811 1157 info@joerns.co.uk • www.joerns.co.uk Índice 1. El elevador de pacientes Oxford Presence ..........69 2. Introducción: Generalidades sobre el elevador ..........70 3. Instrucciones de montaje y encargo............71 4. Precauciones de seguridad ................75 5.
Oxford ® E s p a ñ o l Presence 1. El elevador de pacientes Oxford Presence Larguero Unidad de control de batería Asa de empuje Barra de extensión Actuador eléctrico Extrusión de mástil Ruedas traseras (con freno) Ruedas delanteras (sin frenos) 294000.10007 Rev.
Si no está seguro de cuáles son los requisitos de mantenimiento en su área geográfica, consulte con su proveedor y/o con una oficina de la administración local. El Oxford Presence es adecuado para las siguientes CATEGORÍAS de elevador dentro de los parámetros de trabajo de los elevadores especificados en las ESPECIFICACIONES TÉCNICAS.
• DIODO DE CARGA • CARGADOR/SOPORTE DE SOBREMESA ADVERTENCIA El Oxford Presence es pesado y habrá que tener cuidado al levantarlo. Puede que necesite ayuda para sacar el Oxford Presence de la caja. MONTAJE Retire todas las piezas de la caja y colóquelas en el suelo, con cuidado de evitar que el equipo sufra daños en su superficie.
Seite 72
Oxford ® E s p a ñ o l Presence Apriete el conjunto de mástil con el dispositivo de bloqueo del mástil, que está situado en la parte delantera del chasis. ADVERTENCIA Evite que queden atrapados sus dedos. Mantenga los dedos alejados del extremo del mástil al insertarlo en el alojamiento del chasis.
Seite 73
Oxford ® E s p a ñ o l Presence DESMONTAJE El elevador no debe desmontarse excepto para su mantenimiento, reparación y transporte si fuera necesario. Para ello, siga las instrucciones de montaje en orden inverso. VERIFIQUE SIEMPRE LO SIGUIENTE ANTES DEL FUNCIONAMIENTO •...
Seite 74
Oxford ® E s p a ñ o l Presence • Pulse los botones hacia arriba y hacia abajo del control de mano y confirme que el larguero sube y baja. 294000.10007 Rev. D...
Por favor, lea y siga las precauciones de seguridad que figuran más abajo. El funcionamiento y uso del elevador para pacientes Oxford es sencillo y fácil de comprender. Siguiendo estas precauciones básicas de seguridad, las operaciones de elevación serán fáciles y no causarán problemas.
Seite 76
Oxford ® E s p a ñ o l Presence • NO empuje un elevador cargado a velocidades que superen un ritmo de caminar lento (3 kilómetros/hora, 0,8 metros/segundo). • NO empuje el elevador sobre terreno desnivelado o con baches. Especialmente, si está...
Motor actuador 1. Ajuste de las patas Las patas del Oxford Presence son ajustables eléctricamente en cuanto a su anchura. Las patas pueden abrirse para permitir el acceso alrededor de sillas o de sillas de ruedas. Para transferir y para pasar por pasillos estrechos, las patas del elevador deben estar en posición cerrada.
Seite 78
(vea las instrucciones de carga). 8. Eslingas El Oxford Presence tiene la opción tanto de una barra de extensión de seis puntos como de percha de cuatro puntos. Ambos sistemas utilizan diferentes métodos de sujeción y eslingas. El sistema de seis puntos utiliza eslingas con bucles de tejido, que permiten un ajuste de posicionamiento seleccionando diferentes bucles coloreados.
Seite 79
Oxford ® E s p a ñ o l Presence La eslinga del sistema de cuatro puntos va sujeto a los tachones de la percha por medio de un sistema de clip de seguridad (como se muestra más abajo); cada eslinga se suministra con instrucciones.
Seite 80
ADVERTENCIA OXFORD RECOMIENDA UTILIZAR PRODUCTOS AUTÉNTICOS OXFORD. Los sistemas Oxford de eslingas y elevación tienen un diseño que los hace compatibles entre sí. Para obtener información y consejos específi cos acerca del uso y compatibilidad de las eslingas, consulte la etiqueta de la eslinga, o bien comuníquese con su distribuidor local de mercado o con Joerns Healthcare.
Oxford ® E s p a ñ o l Presence 6. Remoción de sistemas de barra espaciadora/ percha SIGA ESTAS INSTRUCCIONES DE MANERA EXACTA El ascensor actual tiene la opción de usar tanto la barra espaciadora de seis puntos ou la percha de cuatro puntos.
Seite 82
Oxford ® E s p a ñ o l Presence REMOCIÓN PRECAUCIÓN: Asegúrese de sostener el peso de la barra de ensanchamiento/percha antes de retirar la chaveta. Para quitar el pasador, oprima la lengüeta del muelle (usando un destornillador eléctrico de hoja plana o semejante) y saque el pasador.
Cuando esté correctamente colocada, oirá un “clic”. La carga del elevador eléctrico Oxford es sencilla y no tienen por qué surgir complicaciones, pero es importante seguir rigurosamente las instrucciones de carga.
Seite 84
Oxford ® E s p a ñ o l Presence ADVERTENCIA MANTENGA las baterías completamente cargadas. Ponga la batería a cargar cuando no esté en uso. Si le resulta más cómodo, póngala a cargar cada noche. El cargador no permitirá...
8. Plan de mantenimiento y lista de comprobación diaria Todos los productos Oxford requieren un mantenimiento mínimo; sin embargo, es necesario llevar a cabo algunas comprobaciones y procedimientos de seguridad. A continuación se indica un plan de tareas DIARIAS. Realizar comprobaciones diarias y mantenimiento, inspección y prueba cada seis meses asegurará...
Seite 86
Oxford ® E s p a ñ o l Presence *ESTAS COMPROBACIONES DEBEN INCLUIR: 1. BARRA DE EXTENSIÓN: Compruebe la barra de extensión para verificar si tiene libertad de rotación y giro. Compruebe si hay desgaste en el pivote ...
Oxford ® E s p a ñ o l Presence 9. Especificaciones técnicas Carga de trabajo segura ..........500 lbs 227 kgs Longitud total máxima ............ 57.5 pulgadas 1460 mm Longitud total mínima ............. 55.1 pulgadas 1400 mm Altura total máxima ............81.3 pulgadas 2065 mm Altura total mínima ............
Oxford ® E s p a ñ o l Presence ESPECIFICACIONES ELÉCTRICAS BATERÍAS ..............12 voltios, tipo ácido de plomo selladas recargables CAPACIDAD DE LA BATERÍA........3,2 amperios hora ENTRADA NOMINAL DEL CARGADOR ....... 230Vca 50/60 Hz SALIDA NOMINAL DEL CARGADOR ......27,4/29,0 VCC@0,8A Protección Frente a Descargas Eléctricas...
Oxford ® E s p a ñ o l Presence 10. Comprobación Joerns Healthcare ha establecido una red de distribuidores y proveedores de excelente reputación, que se ocuparán con mucho gusto de contestar todas sus preguntas respecto a compra, garantía, reparación y mantenimiento.