Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Installation
Installation
1. Place the device on the floor upside down, loosen
the rear leg lock (13) and push the rear leg (12) out
of its resting position. Fold the leg completely and
push it upwards into its end lock position. Secure
the rear leg locking lever. See Fig. 13.
2. Fold the foot pedal (5) until it clicks into place. See
Fig. 4
3. Fold the front legs (7) forwards until they click into
place. See Fig. 5.
4. If necessary, turn the rear stabilising foot (18) until
it clicks into place and secure it with the lever. See
Fig. 6.
5. Now position the device upright. Make sure that all
legs are secured and that the indication for the front
leg locks (9) is in the position "locked". (Fig.7)
6. You must mount the carrying handle (17) yourself.
Insert the distance piece in the holders and tighten
the handle with the bolt provided and the locking
button in the desired position.
7. After installation, the device can be repositioned
easily using the carrying handle and the front and
back (16 and 17). See Fig. 8.
Folding up
Proceed in reverse order:
1. Make sure that the Lock/Unlock switch (4) is in the
"Unlock" position. See Fig. 9.
2. Turn the device around. Loosen the front leg locks
(8) and fold them into their resting position. Fig.10
3. Loosen the foot pedal by loosening its lock (6). Fold
the foot pedal into its resting position. See Fig. 10.
4. Loosen the rear stabilising foot lock and fold it until
it clicks into place. Loosen the rear leg lock and fold
it into its resting position. Secure the lever that locks
the rear leg again. Fig.10
5. You can use the carrying handle at the back to carry
the device when the poppet is folded up and upright.
See Fig. 11 and 12.
Operation
Clamping
1. Place the workpiece against the front fixed jaw (2).
Slide the moving jaw (2) up against the workpiece.
The moving jaw can either be moved by hand or by
using the foot pedal.
2. Slide down the lock / unlock switch to engage the
lock. Press down on the foot pedal to clamp the
workpiece. See fig 13.
m
WARNING: Maximum allowable force on the
foot pedal is 100Kg. Do not stand or jump on the
product, as you can cause injury or damage to the
product.
Releasing
1. Slide up the lock / unlock switch to release the lock.
2. Press down on the foot pedal until it "clicks" to re-
lease the clamp.
12 І 32
3. Slide the moving jaw away from the workpiece. See
fig 14.
You will need to exert a similar pressure on the foot
pedal as was used to initially clamp the workpiece.
m
WARNING: Ensure the workpiece is support-
ed to avoid it falling when the jaw is released.
Clamping on one side of the jaw
On occasion large or awkward workpieces can only
be clamped on one side of the jaws. If this is the case
then avoid excessive use of clamping force. See fig 15.
Clamping square tube
Clamping square tubing or similar material either on the
diagonal or flat side using the grooves in the jaw pads
for alignment.
Clamping square pieces vertically
On occasion tubing or other square workpieces need
to be clamped vertically on the centre of the jaws. Use
the grooves on the jaw pad to align the workpiece. A
hole accommodates workpieces up to 40mm width to
be clamped vertically. See fig 16.
Clamping large objects (clamping range >450mm)
To clamp larger workpieces the moving jaw can be re-
versed to increase the clamping range, up to 956mm.
1. Remove the moving jaw by sliding it from the tracks.
2. Rotate the moving jaw 180° and reassemble. See
fig 17.
m
WARNING: Whenever clamping workpieces
up to the maximum clamping range ensure the work
piece rests down on the moving jaw and remains
parallel to it.
Technical Details
Clamping range
Maximum clamping
force
Maximum load
Clamping method
Clamp travel (per stroke)
Weight
Footprint (standing)
Footprint (folded)
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consuma-
bles.
Wear parts*: clamping jaws
* Not necessarily included in the scope of delivery!
0-450 mm / 0-950 mm
(2 Bereiche)
10000 N
150 kg
Pedal
24 mm
ca. 19 kg
1070 x 980 x 895 mm
815 x 302 x345 mm
Werbung
Inhaltsverzeichnis
