Herunterladen Inhalt Inhalt Diese Seite drucken

Bosch Active Line Purion BUI210: 1 270 020 916 Originalbetriebsanleitung Seite 11

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 4
OBJ_BUCH-2819-002.book Page 2 Monday, May 22, 2017 11:27 AM
As soon as you stop pedaling when in normal operation, or as
soon as you have reached a speed of 25/45 km/h, the assis-
tance from the eBike drive is switched off. The drive is auto-
matically re-activated as soon you start pedaling again and the
speed is below 25/45 km/h.
Options for switching off the eBike system:
– Press the On/Off button 1 of the on-board computer.
– Switch off the eBike battery using its On/Off button (bi-
cycle manufacturer-specific solutions are possible where-
by there is no access to the battery On/Off button; see the
bicycle manufacturer operating instructions).
The system shuts down after being switched off; this takes
approximately 3 seconds. It cannot be switched back on
immediately until shutdown has been completed.
If the eBike is not moved and no button is pressed on the on-
board computer for 10 minutes, the eBike system will shut
down automatically in order to save energy.
Note: Always switch off the eBike system when you park the
eBike.
Note: If the batteries of the on-board computer are empty,
you can still switch on your eBike using the bike's battery
pack. It is, however, recommended that you replace the inter-
nal batteries as soon as possible in order to avoid damage.
Displays and configurations of the on-board
computer
Symbols and their meaning
Symbol
Explanation
short button press (less than 1 second)
medium button press (between 1 second and
2.5 seconds)
long button press (longer than 2.5 seconds)
Energy supply of the on-board computer
The on-board computer is supplied with voltage by two
CR2016 button cells.
Changing the Batteries (see figure A)
If the on-board computer shows "LOW BAT" on the display,
remove the on-board computer from the handlebars by un-
screwing the fastening screw 3 of the on-board computer.
Open the battery lid 10 using a suitable coin, remove the used
batteries and insert new CR 2016 batteries. You can obtain
the batteries recommended by Bosch from your bicycle
dealer.
When inserting batteries, pay attention to the correct
polarity.
Close the battery compartment again and fasten the on-board
computer to your eBike's handlebars using the fastening
screw 3.
Bosch eBike Systems
Battery Charge-control Indicator
The battery charge-control indicator g displays the charge
level of the eBike battery pack. The charge level of the eBike
battery pack can also be checked on the LEDs of the battery
pack itself.
On indicator g, each bar of the battery pack symbol is equiva-
lent to a capacity of approx. 20 %:
The eBike battery pack is fully charged.
The eBike battery pack should be recharged.
The LEDs of the charge-control indicator on the
battery extinguish. The capacity for assisting the
drive has been used up, and assistance is gently
switched off. The remaining capacity is made avail-
able for the lighting. The indicator flashes.
The capacity of the eBike battery pack is enough
for about 2 hours of lighting.
Switching the Push-assistance mode On/Off
The push-assistance feature makes it easier to push the
eBike. The speed in this function depends on the set gear and
cannot exceed 6 km/h (max.). The lower the set gear, the low-
er the speed in the push-assistance function (at full output).
 The push-assistance function may only be used when
pushing the eBike. Danger of injury when the wheels of
the eBike do not have ground contact while using the push-
assistance function.
To activate the push-assistance function, short-press
button "WALK" on your on-board computer. After activation,
press button "+" within 3 s and keep it pressed. The eBike
drive is switched on.
Note: The push assistance cannot be activated in the "OFF"
assistance level.
The push assistance is switched off as soon as one of the
following occurs:
– You release the "+" 6 button;
– The wheels of the eBike are prevented from turning (e.g.
by braking or being hit by your leg);
– The speed exceeds 6 km/h.
Note: On some systems the push-assistance function can be
started directly by pressing the "WALK" button.
English–2
the
1 270 020 XBP | (22.5.17)

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Performance line purion bui210: 1 270 020 916Active line purion bui210: 1 270 020 925

Inhaltsverzeichnis