Elektro Maschinen HDEm 2400Top Line Bedienungsanleitung Seite 11

EN
We wish to thank you for choosing our machine. We are confident that the high quality of our machine will meet with your
satisfaction and appreciation and that your pressure washer will give you long-lasting service. Before starting to use your
machine, make sure to read with care this manual, which has been purposely drawn up to provide you with all the necessary
information for proper use of the machine, in compliance with basic safety requirements.
INDEX
1 Main constructive components
2 General safety advice
3 Connection of water supply pipe
4 High pressure pipe connection
5 Electrical connection of appliance
6 Appliance switch on
7 Appliance switch off
8 Accessories
9 Maintenance and repairs
10 Trouble shooting guide
1
MAIN COMPONENTS (Fig. 1)
1) Power plug
2) Main switch
3) Water supply rapid attachment
4) Filter
5) Turbo nozzle
6) Variable-nozzle jet
7) Spray gun
8) Spray gun safety device
9) Water delivery attachment
10) High pressure pipe
11) Instructions booklet
12) Upper detergent tank
14) Hose Reel Kit (optional)
16) Detergent selector
2
SAFETY PRECAUTIONS
Do not use the device in the vici-
nity of persons, unless they are
wearing the necessary protective
garments.
High pressure jets may be dangerous
if used incorrectly, the jet must never
be directed on persons, live electrical
appliances, including the appliance
itself. Never use the jet to clean your
own garments or footwear.
The high pressure of the water
generated and connection to the
electricity supply constitute parti-
cularly serious danger risks.
Before connecting the appliance to
the electric socket, check that the
electric data corresponds to that of
the power supply network printed
on the identity plate.
Carefully read the user in-
structions before starting the
machine for the first time.
Follow the safety warnings.
The appliance must be used solely by personnel trained
in its use and specifically authorized to use it.
The user manual must be made available to all users.
The hydro cleaning machine is regulated in the factory
and all the safety devices contained are sealed.
Alteration of their regulation is forbidden.
Do not subject the machines to any modifications which
may jeopardize personal safety.
The hydro cleaning machine is classed as a fixed
appliance. Failure to respect this prescription may be
dangerous. The electrical connection must be made
by qualified technicians capable of operating in ob-
servance of the standards in force (for Italy, observe
the provision of Law 46/90 and IEC 364) and in
compliance with the manufacturer's instructions.
Incorrect connection may cause injury to people or
animals and damages to objects, for which the manu-
facturer cannot be held responsible.
The electrical system to which the appliance is con-
nected must be realized in compliance with the laws of
the country of installation. Do not use extensions to feed
the H.P. cleaner. The H.P. cleaner must be connected
to the electric supply by means of an omnipolar switch
with opening contacts of at least 3 mm. This switch must
have electric features which are consistent with the ap-
pliance. The presence of a differential magnetothermal
switch is necessary with a sensitivity of equivalent to 30
mA, above the power socket or the system.
The appliance is disconnected from the electric supply
only by pulling out the plug or switching off the om-
nipolar switch.
Water cleaners with the "Total Stop" device
should be considered as off when the om-
nipolar switch is in the "O" position or the
plug is unplugged from the socket.
Only put the appliance into operation providing that
all components are free of defects.
Firstly check the mains attachment wire, the high
pressure pipe, the spraying device and the body. Do
not tread on the high pressure pipe; do not pull, bend
or twist it.
Do not shift the appliance by pulling it by the high pres-
sure pipe. Never operate with a defective high pressure
pipe, but always replace with original spare.
The high pressure pipe must be homologated for the
permitted working overpressure of the appliance.