Conrad 97 56 50 Bedienungsanleitung Seite 4

If all settings are correct, click on the "Setup" button. This will transfer the confi guration to the router. Then,
the Internet connection is established. After completion, the current status is displayed in the setup window.
☞
During the setup procedure, the router is reset to factory settings. All previous settings will be
lost.
If you want to make further settings after completion of the setup, open the web interface (see General
Information chapter).
c) Web Interface
You can now change the settings according to your requirements.
Amongst others, we recommended to change the user password "admin". To do this, click the "Manage-
ment" menu and then on "Password". Enter "admin" in the fi eld after "User Name" and enter the new secure
password in both fi elds below. Confi rm by clicking the "Apply Changes" button.
When you have completed the confi guration, you can simply close your internet browser. The confi guration
is thus complete.
Bridge (network switch)
a) Confi guration using the software
First, confi gure the WLAN connection of the router using the software provided.
To do this, start the confi guration software again as described in the chapter "Gateway" section b).
Then, select "Anderer Kabel-Provider" as provider and confi rm with "Weiter".
In the next window, click on "Basis Konfi guration" again.
Now you can set up the WLAN connection; observe the section b) in the chapter "Gateway". To complete,
click on "Setup" again in order to transfer the confi guration to the router.
When this is complete, open the web interface of the WLAN router as described in the chapter General
Information.
b) Web interface
First, open the menu "Operation Mode". The highlight "Bridge" and confi rm by clicking "Apply Changes".
Change all required settings now since a later confi guration is only possible when you allocate a fi xed IP
address such as 192.168.1.50 to you computer. For information on how to do this, see section c) in the
chapter "Gateway".
When you have made all settings, click on "Network Settings" and then on "LAN Interface". In the menu
behind "DHCP", change the setting "Server" to "Disabled" and confi rm again with "Apply Changes".
Click "Reboot now" and close your browser. Shut down your computer.
Wait for approx. 20 seconds and switch off the WLAN router.
c) Connection
Now connect one of the 4 LAN sockets of the WLAN router with your existing router or network switch using
a 1:1 network cable. Make sure that one DHCP server must be present in your network.
Wait for a few seconds and switch on your computer and the WLAN router.
When the operating system is loaded, your computer obtains an IP address from the DHCP server of your
fi rst router.
The confi guration is thus complete. You can now connect your devices to the 4 LAN ports or WLAN via the
WLAN router .
Wireless ISP (WLAN client)
Before changing the operation mode, reset the router to factory settings. Observe the chapter Resetting to
Factory Settings.
a) Confi guration with Quick Setup
Open the web interface of the WLAN router.
Then go to the menu "Quick Setup" and select "Wireless ISP". Confi rm by clicking "Next".
Here you must select the connection type of the WAN interface. Usually, this is "DHCP Client". Confi rm by
clicking "Next".
☞
The settings for the WLAN connection must be made in the next two windows. You can do this
manually at this point or search for the desired WLAN after completion of the Quick Setup. In this
case, leave the settings in both confi guration windows "Wireless Basic Settings" and Wireless
Security Setup" as specifi ed. Confi rm by clicking "Finished" and continue with point b).
If you know the settings for the WLAN and want to enter them manually, enter the name of the WLAN network
you want to use to connect to the internet in the fi eld "SSID". Check all other settings and adjust them accord-
ingly, if necessary. Click "Next" again.
In the next window, you must select the encryption and the format of the code. Enter the WLAN key in the
fi eld "Pre-Shared Key". Click "Finished" to complete.
The router restarts and connects automatically to the specifi ed WLAN. The status page is shown as soon as
this procedure is complete. Here you can see whether the connection was successful. "Connected" must be
displayed behind "State" under "Wireless Confi guration".
Skip point b) and continue with c).
b) Alternative confi guration
After completing the Quick Setup, click on "Wireless" and then on "Site Survey".
Click the "Site Survey" button on this page to search for available WLAN networks.
Select the desired network using "Select" and confi rm with "Next."
On the next page, enter the WLAN key in the fi eld "Pre-Shared Key". All other settings are usually transferred
automatically. Click "Connect" to complete.
If the connection was made successfully, "Connect successfully" is now shown. Click "OK".
c) Completing the Confi guration
The basic confi guration is thus complete. You can now make further settings in the web interface. For infor-
mation on how to do this, see section c) in the chapter "Gateway".
To complete, simply close your web browser.
You can now connect your network devices to the LAN ports 1 to 4. If desired, you can add a network switch.
Unfortunately, connection to the WLAN router is not possible in this operating mode.
Resetting to Factory Settings
On the bottom side, there is a countersunk reset button, with which the WLAN router can be reset to the
factory settings.
Connect the router with the power adapter and plug it into a mains socket. Switch the WLAN router on and
wait for 20 seconds until the self-test is complete. Then press and hold the "Reset" button for longer than
about 6 seconds. The WPS-LED lights up after approx. 2 seconds. When it goes out, you can release the
button.
The router restarts; this takes about 20 seconds. Then it is reset to the factory settings (IP address
192.168.1.1; username "admin" and password "administrator").
Handling
• Any maintenance or repair work may only be carried out by authorised personnel.
• Check the product for damage before each use!
If you detect any damage, DO NOT connect or use the product! This may present a danger to
life!
• A safe operation can no longer be assumed, if:
- the product shows visible signs of damage,
- the product does not function or does not function properly (e.g., if it produces a smell of
burning)
- the product was stored under unfavourable conditions
• When setting up the product, make sure that the cables are neither kinked nor pinched.
Maintenance and Cleaning
The product does not require any maintenance and should never be disassembled for any reason.
Disconnect the product from the power supply before cleaning, unplug the wall plug transformer from the mains
socket (all network connections will cease to function). Disconnect the RJ45 cable, if necessary.
Dust can easily be removed using a clean, soft brush and a vacuum cleaner.
Do not use aggressive cleaning agents as these can cause discolouration.
Do not press too strongly on the surface, to prevent scratch marks.
Disposal
Electrical and electronic products do not belong in household waste!
Dispose of the unserviceable product according to the relevant statutory regulations!
Declaration of Conformity (DOC)
Hereby, we, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau (Germany), declare that this
product complies with the essential requirements and relevant regulations of the guideline 1999/5/EG.
☞
The Declaration of Conformity for this product can be found at www.conrad.com.
Technical Data
a) WLAN Router N300
Operating voltage ........................12 V/DC
Network adapters ........................4 RJ45, 10/100MBit
WAN port .....................................RJ45, 10/100MBit
WLAN ..........................................802.11b/g/n (max. 300MBit)
b) Power adapter
Operating voltage ........................100-240 V/AC, 50/60 Hz, 0.2 A
Output ..........................................12 V/DC, 0.5 A
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2011 by Conrad Electronic SE.