Conrad 97 56 50 Bedienungsanleitung Seite 3

O P E R A T I N G I N S T R U C T I O N S
WLAN ROUTER N300
Item no. 97 56 50
Intended use
The product is provided with 3 different functions. It can be used as WLAN router (Gateway), network switch
(Bridge) or WLAN client (Wireless ISP).
The power is supplied from the power adapter included in the delivery.
Always observe the safety instructions and all other information included in these operating instructions.
This product complies with the applicable National and European requirements. All names of companies and
products are the trademarks of the respective owner. All rights reserved.
Contents
• WLAN router N300
• Power adapter
• Network cable
• Software
• Operating instructions
Features
• WAN port for external DSL or cable modem (with network connection); no modem installed
• WLAN using 802.11b/g/n (max. 300 Mbit); WLAN antenna mounted on the router
• 4-port 10/100MBit switch integrated
• On/Off switch at the rear side
• The power is supplied via the enclosed power adapter
LEDs on the WLAN router
Power Lights up when the device is supplied with power
WAN Lights up if a device is connected to the WAN port; blinks rapidly during data transfer
WLAN Lights up when WLAN is activated; fl ashes quickly during data transfer
WPS Lights up during reset; fl ashes slowly if WPS is active
LAN 1-4 Lights up if a device is connected to the RJ45 port; fl ashes quickly during data transfer
Safety Instructions
Prior to starting up the product, read the operating instructions entirely; they contain
important information on the correct operation.
The warranty will be void in the event of damage caused by failure to observe these safety
instructions! We do not assume any liability for any consequential damage!
Nor do we assume any liability for material and personal damage caused by improper use
or non-compliance with the safety instructions! In such cases the warranty will be null
and void.
• The unauthorised conversion and/or modifi cation of the product is not permitted for reasons
of safety and authorisation regulations (CE). It must not be opened or dismantled! It does not
contain any internal parts that need to be adjusted or maintained by you.
• The product is only intended for use in dry, indoor locations. No part of the product should be al-
lowed to become moist or wet; never take hold of it if your hands are wet!
There is a risk of a life-threatening electric shock!
• The design of the wall plug transformers complies with protection class II. Only connect the
power adapter to a standard mains socket connected to the public supply.
• Only use the enclosed power adapter for power supply.
• The product is not a toy. Keep devices that operate on the mains voltage out of the reach of
children. Therefore, be especially careful when children are around.
• Further, protect the product from direct sunlight, strong heat (>35°C), cold (<0°C), dust and dirt,
splashes and dripping water, vibrations or mechanical loads.
• When the product is taken from a cold to a warm room (e.g., during transport), condensation
may be produced. This could damage the product. This might cause a lethal electric shock!
Wait until the product has reached room temperature before using it. This may take several
hours.
• Do not leave packing materials unattended. They may become dangerous playthings for children.
• In commercial institutions, the accident prevention regulations of the Employer's Liability In-
surance Association for Electrical Systems and Operating Materials are to be observed.
• In schools, educational centres, hobby and self-help workshops, the operation of the product
has to be supervised by trained employees.
• Handle the product with care. The product can be damaged if crushed, struck or dropped,
even from a low height.
• If questions which are not clarifi ed in these operating instructions arise, please contact our techni-
cal support or another specialist.
The Operation Modes
www.conrad.com
a) Gateway (WLAN router)
In "Gateway" mode, the product can be used as a WLAN router for DSL, cable connection or with fi xed IP
Version 07/11
address. In this case, the DSL or cable modem must be connected to the WAN port. The router then func-
tions as DHCP server.
Confi guration for DSL or cable access can be done very easily using the software provided.
b) Bridge (network switch)
In the "Bridge" mode, the LAN connections 1 to 4 as well as the WLAN are bypassed. This is similar to a
network switch with an additional WLAN access point.
No WAN and Firewall functions are supported. The WAN port may not be used.
c) Wireless ISP (WLAN client)
In the "Wireless ISP" mode, the WLAN is the WAN port, i.e. the internet connection is established via WLAN,
e.g. in a public hotspot or a hotel. The network connections are likewise bypassed here. The router functions
as DHCP server and provides its own network.
General Information
• The IP address of the WLAN router is 192.168.1.1.
• The WLAN is encrypted with WPA2/AES upon delivery. The password is "12345678".
• In order to open the web interface, you must either enter "http://192.168.1.1/" in the address box or click
the "Webinterface" button in the confi guration software.
User name and password for the web interface are "admin" and "administrator".
• In order to run the "Easy Setup" on the CD provided, Internet Explorer 7 or higher must be installed.
• The WLAN router also has 2 buttons on the sides.
Using the "WLAN" button you can switch the WLAN connection on or off. To do this, keep the button
pressed for at least 2 seconds. It then takes a few seconds until the connection is switched on/off.
The button "WPS" can be used for a quick connection with other WLAN devices, e.g. a WLAN USB stick,
which must also be able to support WPS. Keep the button pressed for approx. 3 seconds to establish
the connection. When the WPS-LED starts fl ashing slowly, you can release the button. Now press the
WPS button on your WLAN adapter to establish the connection. This process may take several minutes.
Observe the operating instructions for your WLAN adapter.
Connection and Getting Started
• Take the WLAN router out of its packaging and place it on an even, plane surface.
• First, connect the LAN socket of your computer with one of the 4 LAN sockets of the router using a 1:1
network cable.
• Next, connect the power adapter to the WLAN router and connect it to a mains socket.
• Then, switch the router on. The switch is situated on the rear of both connection sockets.
The WLAN router now runs a self-test. This can take up to 1 minute.
Preparing Your Computer
• Switch your computer on and wait until the operating system has loaded completely.
• Regardless for which operation mode you want to confi gure the router, the operating system must always
be set in a way that the IP address of the network connection is obtained automatically from the router.
This is normally the default setting in Windows.
You can alter this setting in the Properties of the LAN connection under the point Internet Protocol TCP/IP 4.
Gateway (WLAN router)
a) Connection
First, connect the WLAN router using a 1:1 network cable to your DSL or cable modem and switch this on.
b) Confi guration using the software
Insert the provided CD with the installation software into your DVD drive. If Auto Play is activated in your
computer, the selection menu will now start automatically.
☞
To start the confi guration, press "Easy Confi guration" in the menu. If the program does not start, please
start the software manually (at the time of preparing this manual the programme "vbpES.exe" in the path "\
fscommand\Easy_Setup\English\" of the CD should be started).
☞
Select your provider on the fi rst confi guration page of the software. The list contains DSL providers as well as
cable providers. If your provider is not present, select "Anderer DSL-Provider" or "Anderer Kabel-Provider".
If necessary enter your access data that you received from your provider.
☞
Click the "Weiter" button to continue.
If you also want to set up the WLAN connection with the confi guration software, click on "Basis Konfi gura-
tion". The other button transfers the previous settings to the router and then opens the advanced confi gura-
tion in the web interface.
You can change the name of the WLAN connection in the "ESSID" fi eld (special characters are not allowed).
Set the desired channel for the WLAN in the "Default channel" menu. If you are unsure which channel your
other devices use, select "Auto".
WPA2 is the default setting for the encryption. We recommend that you keep this selection. If you should need
another encryption, change the settings accordingly.
Finally, enter a secure password for the encryption.
If this is the case, please open Windows Explorer and change to the DVD station. Next, start the
directory "Autorun.exe". This can be found in the master directory on the CD.
In some cases it may happen that the software of the anti virus software or your fi rewall is being
blocked. Adjust the settings in your safety software or deactivate this temporarily, so you can
continue with the confi guration.
You can exit the software at any time by clicking on the "Exit" button.
Press the "Web Interface" button to open the web interface immediately from the software.
For default providers, all additions, e.g. "@t-online.de" to be added to the username are pre-set.
Possible additions must be specifi ed only when "Anderer DSL-Provider" was selected.