Technical Specifications - BRAX MultiController Installationsanleitung

Mainboard features:
There is a red LED located next to the fuse holder. During normal operation, this LED flashes at a
selected refresh rate. In the case of any fault detected upon power-on reset (EEPROM not respond-
ing correctly) the LED will stay off and the fault must be rectified.
Next to the LED, there are two small PCB pads designated as KEY (
with screwdriver and then you turn on the device, both remote temperature sensors will be recali-
brated. After recalibration the LED will stay on, thus indicating that new calibration constants have
been saved successfully to EEPROM. You must restart device in order to see the effect of recalibra-
tion. Please ensure that both remote sensors have the same temperature as reference on-board
sensors while recalibrating.
If you short the KEY during normal operation you will see on display temperature
measured by reference on-board sensor instead of remote sensor for channel 1.

Technical specifications

Measurement ranges:
Current: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0,5 - 200 A ±2%
Voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 18 V ±0,1 V
Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3600 W
Temperature: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -15° C +125° C ±1° C
Sampling frequency: . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Hz
Electrical characteristics:
Supply voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18 V DC
Current consumption:
Mainboard operating . . . . . . . . . . . . . . . . . . . . . . . . . . < 70 mA
Mainboard+Display idle . . . . . . . . . . . . . . . . . . . . . . . . < 3 mA
Display operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 mA max.
Mainboard remote input . . . . . . . . . . . . . . . . . . . . . . . < 5 mA
Display remote input . . . . . . . . . . . . . . . . . . . . . . . . . . < 5 mA
Operating temperature: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40 ° C + 85° C
Fan output current: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mA max.
Internal shunt resistance: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0,001 Ohm
Applicable display settings:
Display mode:
Refresh rate:
Brightness:
Over-temperature:
Temperature scale:
AUDIOTEC FISCHER GMBH · Huenegraeben 26 · D-57392 Schmallenberg
Internet: audiotec-fischer.com · Email: info@audiotec-fischer.com
2 options
AVERAGE / PEAK
10 steps
0,1 / 0,2 / 0,3 / 0,4 / 0,5 / 1,0 / 1,5 / 2,0 / 2,5 / 3,0 seconds
10 steps in 2 individual presets for LIGHTS are "ON" or "OFF"
10 steps
50 / 55 / 60 / 65 / 70 / 80 / 90 / 100 / 110 / 120 °C
122 / 131 / 140 / 149 / 158 / 176 / 194 / 212 / 230 / 248 °F
2 options
°C / °F
Tel.: ++49(0)2972-97880 · Fax: ++49(0)2972-978888
I I I I ). If you short the KEY e.g.