Technical Data; Attachment And Operation - Scheppach 5911001901 Originalbetriebsanleitung

• Safety hazard from the electric tool in case of long
hair and loose clothing; Wear personal protective
equipment such as a hair net and tight work cloth-
ing.
• Although having regarded all considerable rules
there may still remain not obvious remaining haz-
rds.
• Minimize remaining hazards by following the in-
structions in "Safety Rules", "Use only as author-
ized" and in the entire operating manual.

6. Technical data

Dimension L x W x H
Air speed min./max.
air volume min./max.
Wheel diameter
dust bag capacity
Engine
Motor speed max.
Engine output
Weight
Subject to technical changes!
Information concerning noise emission measured ac-
cording to relevant standards:
Sound pressure L = 86.6 dB(A)
pA
Sound power L = 100 dB(A)
WA
Uncertainty K = 2 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration A = 0.82 m/s
2
hv
Uncertainty K = 1.5 m/s
2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked
the places that have to do with your safety with
this sign: m
22 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
770 x 160 x 1110 mm
165 / 275 km/h
10 / 13.5 m /min
3
70 mm
45 l
230 / 50 V / Hz
14000 rpm
2800 W
3.2 kg

7. Attachment and operation

ATTENTION! Before working on the device - clean-
ing, inspection, maintenance or other work - always
turn off the device and separate it from the power
supply.
ASSEMBLY
m The Vac-blower must not be used or switched
on until it has been fully assembled.
Height adjustment (Fig. 2 + 3)
• Press the button (2.1) and slide the air duct (5). It
can be adjusted up to 300mm.
Fitting the collection bag (Fig. 4 + 5)
m Before fitting the collection bag ensure
that the Vacuum/Blow selector lever operates
smoothly and that it is not obstructed by debris
from the previous use.
To install the collection bag
• Turn the support frame (4.1) into the correct posi-
tion of the housing (4.3).
• Lock the support at its place.
To dismantle the collection bag:
• Press the support (5.1) to release.
m The user must carry the bag's weight alone.
Fitting the shoulder harness (Fig. 6)
The Vacuum-Blower is provided with a shoulder har-
ness (6.1) this is attached to the top of the main body
of the Vacuum-Blower (6.2). The shoulder harness
is provided to reduce fatigue and aid comfort when
using the Vacuum-Blower and can be worn in a po-
sition to suit the operator.
Never put the shoulder strap over your shoulder
and across your chest, but put it on one shoul-
der. In this way, you will be able to quickly re-
move the tool from your body in case of emer-
gency.
m Warning! Use only original manufacturer's re-
placement parts, accessories and attachments. Fail-
ure to do so can cause poor performance, possible
injury and may void your warranty. Never use the
machine without the guard assembled!
Operation
Before starting
• Plug the Vacuum-Blower into the mains supply via
the (R.C.D.) and switch on. Check that the (R.C.D.)
is operating correctly.