Operation; Cleaning, Maintenance And Ordering Of Spare Parts; Replacing The Blade; Disposal And Recycling - EINHELL GC-CT 18/24 Li Originalbetriebsanleitung

All LEDs fl ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.

6. Operation

To obtain maximum performance from your grass
trimmer, please follow these instructions:
•
Never use the grass trimmer without the
guard.
•
Do not mow grass when it is wet. The best
results are achieved with dry grass.
•
To switch on your grass trimmer, press the
ON/OFF switch (Fig. 11/Item 1).
•
To switch off your grass trimmer, let go of the
On/Off switch again (Fig. 11/Item 1).
•
Do not allow the grass trimmer near the grass
until the switch is pressed, i.e. the grass trim-
mer is in operation.
•
To cut properly, swing the machine sideways
while moving forwards. Keep the grass trim-
mer inclined at an angle of approx. 30° while
you do so (see Figs. 15 and 16).
•
If the grass is long, the grass must be cut
shorter in stages, starting from the tip (see
Fig. 17).
•
Use the guard hood to prevent unnecessary
wear.
•
To avoid unnecessary wear, keep the grass
trimmer away from hard objects.
•
To use the edge guide along walls or objects,
swing the edge guide forward to the front (Fig.
18). Swing it up when not in use (Fig. 19).
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Before putting away or cleaning the grass trim-
mer, switch off and remove the battery pack.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend that you clean the equipment
immediately after you use it.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
Anl_GC_CT_18_24_Li_Solo_SPK9.indb 24 Anl_GC_CT_18_24_Li_Solo_SPK9.indb 24
GB
cleaning agents or solvents; these may be ag-
gressive to the plastic parts in the equipment.
Ensure that no water can get into the interior
of the equipment. The ingress of water into an
electric tool increases the risk of an electric
shock.
•
Use a brush to remove deposits from the
safety guard.

7.2 Replacing the blade

Danger! Be sure to remove the battery pack
before replacing!
•
Push the blade to the inside (Fig. 20) and re-
move it through the larger opening.
•
To fit the new blade, proceed in reverse order
(Fig. 10). Make sure the blade locks into place
correctly as shown in Fig. 20.
7.3 Maintenance
There are no other parts inside the equipment
which require maintenance.
7.4 Ordering spare parts
Please provide the following information on all
orders for spare parts:
•
Model/type of the equipment
•
Article number of the equipment
•
ID number of the equipment
•
Spare part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info

8. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Defective components must be dispo-
sed of as special waste. Ask your dealer or your
local council.

9. Storage

Store the equipment and accessories in a dark
and dry place at above freezing temperature. The
ideal storage temperature is between 5 and 30
°C. Store the electric tool in its original packaging.
- 24 -
19.10.2017 13:03:28 19.10.2017 13:03:28