WMF Stelio Gebrauchsanweisung Seite 5

Start-up
Wash the removable parts before initial use. Leave any excess power cable which
is not required in the cable compartment and insert the cable in the notch
provided. Connect the power plug to a mains socket.
Place the juice collector and strainer on the appliance along with the right
reaming cone to fit the size of the fruit.
Note: The small reaming cone is located within the large reaming cone.
If using the large reaming cone, place it on the small reaming cone with the pulp
extractor. It will click into place. Then place a glass under the pouring lip. Halve
the citrus fruit and, with the cut end facing down, place one half at a time on the
reaming cone and press down. The motor will start up automatically as the appli-
ance has an automatic start-stop function. The juice flows through the strainer,
which catches the pulp and pips, into the juice collector and through the pouring
lip into the glass. The machine stops operating when the pressure is no longer
applied. Repeat this process a few times to extract as much juice as possible from
the fruit. The motor may stop working if too much pressure is applied. In this case
reduce the pressure. Before serving the glass of juice, close the pouring lip by
taking hold of it on both sides and pushing it upwards. If you intend to use the
juicer again after a short time, place the cover on the machine in the interests of
hygiene while it is out of use. Citrus juice should be drunk while fresh. Under no
circumstances should the juice ever be stored in metal containers.
Cleaning and maintenance
Remove the power plug after use. It is advisable to wash the removable parts
immediately after use, either with hot water and washing-up liquid or in the
dishwasher. Do not use scouring agents.
Pull the reaming cone straight up to remove it. Never immerse the motor housing
in water - just wipe the outside clean with a damp cloth.
8
For UK use only
▪ This product is supplied with a 13 A plug conforming to BS 1363 fitted to the
mains lead. If the plug is unsuitable for your socket outlets or needs to be
replaced, please note the following. If the plug is a non-rewireable one, cut
it from the mains lead and immediately dispose of it. Never insert it into a
socket outlet as there is a very great risk of an electric shock.
▪ The replacement of the plug at the mains lead has to be done according to the
following instructions:
▪ Important: The wires in this mains lead are coloured in accordance with the
following code:
blue Neutral
brown Live
▪ As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug,
proceed as follows:
⋅ the wire which is coloured blue must be connected to the terminal which
is marked with the letter N or coloured black,
⋅ the wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
▪ Do not connect any wire to the terminal which is marked with the letter E or
by the earth symbol , or coloured green or green and yellow.
▪ If a 13 A (BS 1363) plug is used it must be fitted with a 3 A fuse conforming
to BS 1362 and be ASTA approved. If any other type of plug is used, the
appliance must be protected by a 5 A fuse either in the plug or adapter or at
the distribution board.
If in doubt - consult a qualified electrician.
▪ Never use the plug without closing the fuse cover.
The appliance is compliant with European Directives 2014/35/EC, 2014/30/EC and
2005/32/EC.
This product may not be disposed of in normal household waste at the end of its
service life, but must be delivered to a collecting point for recycling electrical and
electronic appliances.
The materials are reusable in accordance with their identification. You will make
an important contribution to the protection of our environment by recycling
used appliances.
Please ask about the responsible disposal point at your community offices.
Subject to change
9