Conrad N150 Bedienungsanleitung Seite 4

Establishing a connection with the second WLAN-SSID of the AP
• Besides the above described SSID, the access point provides a second WLAN network. This
is called "ap-game-xxxxxx". It is encrypted with WEP by default and deactivated on delivery.
• This WLAN is for devices, like game consoles, which only support WEP encryption.
• The name as well as the safety key are again printed on the bottom of the device and are
different for each access point. Every "x" represents a number or letter.
• The WLAN can be switched on and off by using a slide switch which is located on the left
side.
☞
Please note! In the "ON" position the safety switch is activated and the WLAN "ap-
game-xxxxxx" is therefore switched off! Move the switch to the "OFF" position to
activate it.
If you do not need this second WLAN, then leave the slide switch in the "ON" posi-
tion!
• If you wish to connect a device to the "ap-game-xxxxxx" WLAN, slide the switch on the side
to the "OFF" position and wait a few seconds.
Now you can connect each device to the access point.
☞
Please observe the operating instructions of the device in question.
The web interface of the AP
• The device has a web interface like any other access point or router. Here all settings can be
entered.
☞
Please note! For normal use, the settings in the web interface do not need to be
adjusted.
• In order to still access the settings in the web interface, please proceed as follows.
• First you disconnect the network connection between the access point and the router or
network switch by removing the network cable from the AP.
Now reset the access point. In order to do so, remove the power for about 5 seconds.
If the computer on which you want to do the confi guration of the web interface was already
connected to the AP via WLAN, restart this again as well.
After both the access point and the computer have completed the reset process, reconnect
your computer with the WLAN of the AP. The connection may also be possibly be restored
automatically.
• Next open your web browser and enter the IP-address http://192.168.1.250/ or http://
ap.setup/ in the address bar.
A screen will open in which you have to enter the user name "admin" and the default pass-
word "password", all in lower case letters and without quotes.
On the fi rst page of the web interface you can start a short Quick setup, in which you can
adjust the settings for the second "ap=game-xxxxxx" WLAN, by clicking on "ENGLISH".
In order to open the extended setup, simply click on "ADVANCE SETTING" on the fi rst page.
• After you have completed the confi guration, close the web browser.
Reconnect the previously disconnected LAN cable to the access point again.
Restart both your computer and the AP again.
Resetting to Factory Settings
On the left side of the device you will fi nd a recessed reset button next to the safety switch. You
can use this to reset the access point back to factory settings.
Connect the access point with the power adapter and plug it into a mains socket. Wait about
60 seconds until the self test has fi nished. Hold the reset button for about 3 seconds until the
power LED starts blinking. Then let go of the button again.
The access point restarts, this takes about 60 seconds. Then the access point is reset to the
factory settings (IP address 192.168.1.250; username "admin" and password "password").
Handling
• Any maintenance or repair work may only be performed by an authorised repair
shop.
• Check the product for damage before each use!
If you detect any damage, DO NOT connect or use the product! This may present
a danger to life!
• A safe operation can no longer be assumed, if:
- the product shows visible signs of damage,
- the product does not function or does not function properly (e.g., if it produces a
smell of burning)
- the product was stored under unfavourable conditions
• When setting up the product, make sure that the cables are neither kinked nor
pinched.
Maintenance and Cleaning
The product does not require any maintenance and should never be disassembled for any
reason.
Disconnect the product from the power supply before cleaning, unplug the wall plug trans-
former from the mains socket (all network connections will cease to function). Also disconnect
the RJ45 cable.
Dust can easily be removed using a clean, soft brush and a vacuum cleaner.
Do not use aggressive cleaning agents as these can cause discolouration.
Do not press too strongly on the surface, to prevent scratch marks.
Disposal
Electrical and electronic products do not belong in household waste!
Please dispose of the product, when it is no longer of use, according to the current
statutory requirements.
Technical Data
a) Access point
Operating voltage ................. 5 V/DC
Network connection .............. RJ45, 10/100Mbit
WLAN ................................... 802.11b/g/n (max. 150Mbit)
b) Power adapter
Operating voltage ................. 100-240 V/AC, 50/60 Hz, 0.3 A
Output ................................... 5 V/DC, 0.8 A
Declaration of Conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that
this product conforms to the fundamental requirements and the other relevant regulations of
the directive 1999/5/EC.
☞
The Declaration of Conformity (DOC) for this product can be found at www.conrad.com.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2011 by Conrad Electronic SE.