Hama Superb Bedienungsanleitung Seite 4

g Operating Instruction
ENCLOSURES
OVERVIEW OF THE UNIT
1. ILLUSTRATION
1
7
2
6
4
3
5
9 10
8
1. Clamp
2. Speaker
3. TALK Button
4. END Button
5. Quick Dial Button
6. LCD
7. MIC
8. Earphone Jack
9. JOG Button
10. Charging port
2. DISPLAY
1 2 3 4
6
7 5
1. Bluetooth Connection
2. MIC Mute
3. Call Activation
4. Battery
5. Volume
6. RSSI (Received Signal Strength Indication)
7. Status display
HANDSFREE MODE
1. TURNING ON/OFF
Hold up LCD panel to turn on the unit.
Pull down LCD panel to turn off the unit.
6
00089385bda.indd Abs2:6-Abs2:7
• POWER SAVING
LCD Backlight is automatically off after 60 seconds.
Press any button once in order to light on again.
2. PAIRING
Press End button for 3 seconds to enter the
Pairing mode until you see blue LED blinking.
Be noted that Pairing mode remains for 60 seconds. If you
stop the Pairing mode, you can push End button
shortly once.
1. Set your mobile phone to 'discover' this unit by
following your mobile phone instruction.
2. Your phone will fi nd the unit model name and ask if you
want to pair with it. Then, confi rm this by pressing 'yes'
or 'OK'.
3. Enter PIN number '0000'(4 zeros), then press 'yes' or
'OK' on your mobile phone. Beep is heard from the unit
after successful pairing.
• AUTO CONNECTION
This unit functions Auto Connection that makes it
possible to be automatically connected to the last
connected phone after turned on.
MAKING A CALL
1. Last Number Redial
Press TALK button one time after connected
with a mobile phone.
Phone number is displayed on the phone. Make a call by
pressing TALK button one time.
2. Number Dial
5 last incoming call numbers are displayed on LCD by
moving right JOG button.
A desired number can be selected by moving JOG button
left and right. Or, if you move left JOG button, numbers in
Phonebook are displayed. Press TALK button
one time for making a call.
3. Quick Dial
With this quick-call button you can dial a number stored
underneath at the touch of a button.
Press Quick Dial button(H) one time to dial the hotline
number stored. You can set a Quick Dial number on
the menu mode. Please refer to Menu mode' from this
manual.
4. RECEIVING A CALL
This unit rings when a call is coming in and the caller
ID(number or name) is displayed on LCD. Press TALK
button to answer a call.
• Caller ID : A caller's name will appear on LCD if the
caller's number is stored in this unit under the name.
REJECTING / ENDING A CALL
1. Rejecting a call
When the unit rings, press END button one time
to reject a call.
2. Ending a call
Press END button one time to end an active call
during a call.
6. TRANSFERRING A CALL
During an active call, press TALK button one
time to transfer a call from the unit to a mobile phone or
from a mobile phone to the unit.
7. ADJUSTING A VOLUME
Move JOG button left and right during a call to adjust the
volume level.
When you move right/left the JOG button, the volume is
up/down.
8. MUTING THE MICROPHONE
If you press JOG button one time during an active call, the
other party can not hear you. To end the mute function,
press JOG button one time again.
9. RESET OF THE UNIT
Press END button for about 8 seconds to reset
the unit then "RESET" shall be displayed on LCD. In this
case, paired device information, selected ring tone,
and incoming call list become all reset only except
phonebook information. Plus, the unit shall automatically
start pairing due to the reset of paired device.
Regarding resetting the phonebook information as well,
please refer to RESETTING THE PHONEBOOK' on this
manual.
[Note] Be careful about losing all information saved in
this unit due to this reset process.
MENU MODE
Please make sure that the device is not connected with
the mobile phone. Only then you can call the menu mode.
1. Entering the menu mode
Press JOG button for about 2 seconds until "MENU
MODE" is displayed on LCD.
2. Ending the menu mode
Press END button one time to escape in present
state.
3. Menu mode scrolling
Search a desired menu by moving JOG button left and
right.
4. Selecting a menu mode
Select a desired menu by pressing JOG button one time.
5. Storing a menu mode
Present menu is stored when you press JOG button for 2
seconds and release.
6. USING A MENU MODE
Menu mode consists of Ring Tone, Phone Book, and
Hotline.
1. Ring Tone
Press JOG button for about 2 seconds to enter the
menu mode. Move JOG button left and right to search the
ring tone menu. Press JOG button one time to enter the
ring tone menu. Move JOG button left and right to fi nd the
desired ring tone from 0 to 2. Press JOG button for about
2 seconds to store the menu mode then the menu mode
shall be ended.
2. Phonebook
Press JOG button for about 2 seconds to enter the
menu mode. Move JOG button left and right to search
the phonebook menu. Press JOG button one time then
phonebook list is displayed. Move JOG button left and
right then 5 lists shall be on.
A list with no number is shown as Empty List. A list that
contains only phone number shows the phone number,
while a list stored along with the name displays the name
after showing the phone number.
Press JOG button if you want to newly change a specifi c
list. When the cursor is shown on LCD, fi nd the number
moving JOG button left and right.
13.06.2007 13:58:22 Uhr
7