Conrad Alatech Cyclaid 10 BLE Bedienungsanleitung Seite 4

Installation of the bicycle computer
Step 1:
• Set the bracket on the handlebar stem; place the rubber strips between the handlebar stem
and the bracket. The rubber strips prevent the bracket from slipping.
Step 2:
• Attach the bracket to the handlebar stem using cable ties.
Step 3:
• Set the bicycle computer on the bracket at about a 45° angle, as shown in the picture.
Step 4:
• Turn the bicycle computer to the right by 45°, until it clicks into place with an audible "Click!".
Getting Started
Initial Start Up
• Briefly press the " " button (12) to end the standby mode and activate the display.
• Next, is set the language for the display indicator with the "
• End the language setting with the "
Basic Information for Operation
• Starting from the main menu, select the desired function with the "
• Confirm a function/setting with the "
• Then change the function/setting with the "
• Leave the setting mode by pressing the "
ter is in standby mode again (display indicator turns off).
The detailed instructions in English, please visit the manufacturer's website
www.alatech.com download.
Pairing
Before the bicycle computer can receive wireless data from the respective sensors (pulse rate
chest band, pedal sensor, wheel sensor), these sensors must be connected to the bicycle
computer. This process is called "pairing".
In this way, the bicycle computer learns which wireless data are intended for it. For this reason,
no disruptions can be caused by other Bluetooth
signals are ignored.
During the "pairing" process, the bicycle computer and the device to be learned (pulse rate
chest band, pedal sensor, wheel sensor) should not be too far removed from one another. Also
keep other Bluetooth devices (like a smartphone with Bluetooth
®
bicycle computer while the "pairing" process is in progress.
Activate the operation of the respective sensor in the corresponding menu of the bicycle com-
puter before you start the "pairing" process.
After the "pairing" starts, the bicycle computer searches for wireless signals (e.g. from pulse
rate chest band, pedal sensor, wheel sensor). Activate the respective sensor as described in
its operating instructions. Also pay attention to the detailed English operating instructions of the
bicycle computer on the "pairing" of sensors.
For example, the chest band is activated when it is put on as usual or when both
contact surfaces are held with both hands.
The wheel sensor or the pedal sensor is activated when the magnet belonging to it
passes by the sensor.
" button (12).
" button (14).
" button (12).
" button (8).
" button (12).
" button (14) repeatedly until the bicycle compu-
devices in the vicinity, since their wireless
®
activated) away from the
®
Maintenance and Cleaning
• Apart from the occasional battery change, the product is maintenance-free for you.
• The outside of the product should only be cleaned with a clean, soft, dry cloth.
Do not use aggressive cleaning agents or chemical solutions that could damage the housing
(discolouring) or impair operation.
Disposal
a) General
Please dispose of the unserviceable product according to the relevant statutory
requirements.
Remove any batteries and dispose of them separately from the product.
b) Batteries and rechargeable batteries
As the end user, you are required by law (Battery Ordinance) to return all used batteries/
rechargeable batteries; disposal of them in the household waste is prohibited.
Batteries/rechargeable batteries containing hazardous substances are labelled with
this symbol to indicate that disposal in domestic waste is prohibited. The designa-
tions for the heavy metals involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead.
Used batteries, rechargeable batteries as well as coin cells can be returned to collection points
in your municipality, our stores or wherever batteries/rechargeable batteries/coin cells are sold.
You thereby fulfil your statutory obligations and contribute to the protection of the environment.
Declaration of conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that
this product conforms to the fundamental requirements and other relevant regulations of the
1999/5/EC directive.
You can find the conformity declaration for this product at www.conrad.com.
Technical Data
Power supply ........................ 1 battery of type "CR2032"
Battery life ............................. approx. 1 year (on the basis of an average daily operating / pub
period of 1 h)
Bluetooth version ................ 4.0
®
Radio frequency ................... 2.4 GHz
Transmission range .............. max. 2 m
Protection type ...................... IPX7
Operating temperature ......... -10 °C to +60 °C
Dimensions ........................... 60.5 x 37.5 x 13.5 mm
Weight .................................. 27.8 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
(www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited. This publication represent the technical status at the time of
printing.
© Copyright 2015 by Conrad Electronic SE.