Delphin CODER Bedienungsanleitung Seite 3

EN: USERS GUIDE
Set of electronic bite alarms
RECEIVER 1
functions.
5 volumelevels(V wheel,including silent mode)
5 different signaling tones (T wheel)
Vibrationmode(togge switch right position)
4 color signaling LEDs
Selected settings stores in memoru
ON/ OFF / VIBRAT O Ntoggleswitch
Memory diode lit continuously for 15sec after the bite
Low batteru indication(continuousbite beep)
Kit range test mode
Range 140mdepending an the terrain
Power supp u lx9V batteru
BUTTON SCHEME
Antenna
Signaling
LEDs
Rotary switch
T / tone
COOER
MANUAL
Before starting: Openthe back cover of the receiver/bite alarm to insert the batteries On the bite alarmbu pullingthe ower part
upwards, on the receiverbu slidingit down The bite alarmis powered bu a lx 23A battery, a receiverbg lx BV Before inserting the batteries,
inspect them properluand make sure that theu do not are leakingor damaged other wau nsert the batteries according to the correct
po aritu (+ and -) Returnthe cover and secureit
Switching the bite alarm ON/ OFF:Buhodingdawnthe red'POWER" button anthe bottom sidefor sec Whenturning on the bite
alarmbeeps 3 times and both color LEDsflash Btimes. When switching off, the bite aarm beeps once and both colorLEDsflash once
Setting the alarm tone: With the bite alarmoff, holddown the red "POWER" b utton for 5 sec The alarmfirst brieflu beeps 3 times
and then a fourth longerbeep sounds After this signal,release the "POWER" b utton and select the desired tone bu turning the switch S
To confirm the selected tone, turn off the alarmbu holding down the red 'POWER" button for
Adjusting the color of the diodes: With the bite alarmoff, ho d down the red "POWER" b utton for 5 sec. The alarmfirst beeps 3 times
and then a fourth anger beep sounds After this signal,releasethe "POWER" b utton and then press it brief u again Rotating switcher S
selects the desired colorof the diodes To confirm the selected color,turn off the alarmbu holding down the red "POWER" button for 2 sec
Position night LEDs:Withthe bitealarmon,the positionLEDs canbe switchedon / off bg brieflypressing the "POWER" button
Pairing the receiver with the bite alarm: With the receiverswitched off and the bite alarmdeviceswitched on,holddown the P button
on the sideof the receiver. Simultaneously s et the toggleswitchto the ON/ eft positionHolddawnthe P button untilthe redandblue
diode light up When these LEDs ight up.releaseit Now brieflu press the P button to select the desired colorand "do the bite" an the bite
a arm gou want to pair,with such as a pieceof paper.To complete the pairingsuccessfully, turn the receiveroff and on
Connection range test: Wth the bite alarmoff, holddown the "POWER" button for 7 sec The alarmbeeps first brieflu 3 times,
then a fourth angerbeep sounds, keepingthe button pressed until a fast continuous beep sounds and LEDsstart flashing
Now gou can move away from the bite alarmwith the receiverto find out how far it is receivingsignals
WARRANTY CARD
Model: Set Delphin CODER
Date of purchase:
Stamp and signature of the seller:
with a receiver
Toggle switch, MODES:
1SOUND -gVIBRATING
O
P / Pairbutton
Rotary switch
v
Delpnin
V / volume
Speaker
/ *keepthis cardcarefullyfor anunecessaryc aims/
After sale warranty service:
After warranty service:
BITE ALARM 1 functions:
Waterproof
5 volumeleves (V wheel,incudingsient mode)
5 different signaling tones
5 sensitivitu evels(wheelS)
7 possible colors of the signaling diode
Selected settings stores in memorg
Backbite signal - different tone
Memore diode lit continuouslu for IS sec after the bite
Low battere indication with a short beep
Position night diade
Non slip rod bed
nput for 2 5 mmjack
Pawersupplulx12V(tupeLR23A)
Memoru diode
Rotaryswitch
V / volume
COOER
'POWER"
ON/OFFbutton
sec.
TECHNICAL PARAMETERS:
Frequency band: 433 92 MHz
RFpower: 5.09 dBm
Bite diode
Rotaru switch
S / sensitivitg
Speaker
nput 2 Smm
connector