Fagor CFC40AX Bedienungsanleitung Seite 16

CAUTION! The side of the truss with connection box
corresponds to the side of the control panel with hood
assembled.
7. Tighten the 4 screws.
8. Insert and tighten another 4 screws in the remaining free
holes for secure fixing.
9. Carry out the electrical connection to the mains power
supply, only turn on the power supply upon completion of
assembly.
10. For extractor versions (10A), connect the other end of the
exhaust pipe to the flue.
For filter versions (10F), fit deflector F to the truss and
secure it to the bracket supplied using 4 screws, then
connect the exhaust pipe to the connection ring located on
the deflector.
11. Couple the two upper sections of the hood to cover the
trellis so that one of the slots present on the sections is
placed on the same side of the control panel (connection
box) and the other on the opposite side.
Screw the two sections together with 6 screws (3 per
side).
12. Fix the upper flue set to the trellis near the ceiling with 6
screws (3 per side).
13. a. Apply the lower/rear section (WITHOUT control
panel) to the rear part of the hood and pre-fix in
position with 2 screws (1 per side).
b. Apply the lower/front section (WITH control panel) to
the front part of the hood,
(b1) connect the electricity between the hood and
the control panel,
(b2) pre-fix in position with 2 screws (one per part),
c. Fix the two sections of the lower sections of the flue
together, using 6 screws (3 per side. Also see the
diagram plan for coupling the two sections).
Note: If the two sections of the lower flue are NOT
perfectly aligned, try loosening all the screws, aligning
the sections of the lower flue and fastening the screws up
again.
14. Apply the 2 tabs (supplied) to cover the fixing points of the
bottom flue (CAUTION! THE BOTTOM FLUE TABS ARE
THE NARROWER AND SHALLOWER ONES).
The wider and deeper tabs are those used for the top flue,
and must be cut to size.
15. Turn the mains power on again at the central electrical
panel and check for correct hood operation.
Installation wall model
Fig. 10-11
Additional warning instructions on installation procedure:
• Check that electric cables are not damaged.
Remove AND CONSERVE the screws that temporarily fix
the flue units (for reasons of transport), the hood or the
flue unit with the suction unit. The two parts should be
disassembled to facilitate installation.
Check how the parts are fixed together to repeat
assemblage at the opportune moment (see also fig. 11
and operation 17).
Attention! The chimney is predisposed for installation of
the filter Version.
In certain models where it is required to use the cooker hood
in the suction version then it is possible to overturn the upper
section of the chimney
and insert it inside the lower section of the chimney so that the
air-exit perforations are not visible.
The chimneys in which this operation is possible are
recognizable by their bracket fixing points G which are
repeated also in the lower side of the upper section of the
chimney.
1. Using a pencil, draw a line on the wall, extending up to the
ceiling, to mark the centre. This will facilitate installation.
2. Rest the drilling template against the wall: the vertical
centre line printed on the drilling template must
correspond to the centre line drawn on the wall, and the
bottom edge of the drilling template must correspond to
the bottom edge of the hood: bear in mind that, when
installation is complete, the underside of the hood must be
at least 50 cm above the cooker top in the case of electric
cookers, and at least 75 cm above the cooker top in the
case of gas or mixed cookers.
3. Rest the support bracket on the drilling template so that it
coincides with the dotted rectangle, mark the two outer
holes and drill them (mark and also carry out upper drill
holes - 3a), remove the drilling template, insert 4 wall
plugs and fix the hood support bracket into place using
two 5x45mm screws.
4. Hang the hood on the bracket.
5. Adjust the distance of the hood from the wall.
6. Adjust the horizontal position of the hood.
7. Remove the carbon filter frame (see also Fig. 3); mark the
drill hole, using a pencil, for fastening the hood to the wall.
8. Remove the hood from the bracket.
9. Drill at the point marked (Ø8mm - see operation 7).
Insert 1 wall plug.
10. Rest the chimney support bracket „G" against the wall,
touching the ceiling. Use the support bracket as a drilling
template (the small slot formed on the support must
coincide with the line drawn on the wall as above –
operation 1) and mark 2 holes with a pencil, dril the holes
(Ø8mm), insert 2 wall plugs.
bracket to the wall using two 5x45mm screws.
11. Hook the hood onto the bottom bracket.
12. Fasten the hood to the wall with 1
(ABSOLUTELY NECESSARY), remount the carbon filter
frame (see also Fig. 3).
13. Connect a pipe (pipe and pipe clamps not provided, to be
purchased separately) for discharge of fumes to the
connection ring located over the suction motor unit.
If the hood is to be used in ducting version, the other end
of the pipe must be connected to a device expelling the
fumes to the outside. If the hood is to be used in filter
version, fix deflector „F" to the chimney support bracket
„G" using 1 screws, and connect the other end of the pipe
to the connection ring on deflector „F".
14. Make the electrical connections.
15. Insert the external covering, of the motor group, half-way.
16. Make all the electrical connections between the two parts
(for major safety during this operation you may fix the
16
Fix the chimney support
5x45 mm screw