Extol 402114 Bersetzung Der Original Bedienungsanleitung Seite 10

5) OPERATING AND MAINTAINING CORDLESS POWER
TOOLS
a) Only charge using the charger specified by the manufacturer.
A charger that may be suitable for one type of battery pack, may lead to
a fire hazard if used with a different battery pack.
b) Only use the tool with a battery pack that is explicitly deter-
mined for the given tool. Using any other battery pack may create
a accident or fire hazard.
c) When the battery pack is not being used, protect it against
contact with other metal items such as paper clips, coins,
keys, nails, screws or other small metal items that could make
a connection between both battery contacts. Short circuiting the
battery contacts may cause burns or a fire.
d) Incorrect use may cause liquids to leak out of the battery;
avoid coming into contact with them. In the event of acciden-
tal contact with these liquids, rinse the affected area with
water. In the event that the liquid enters the eye, seek medi-
cal help. Liquids leaking from the battery may cause inflammations or
burns.
e) A battery pack or power tool that is damaged or modified,
must not be used. Damaged or modified batteries may behave errati-
cally, which may result in a fire, an explosion or an injury hazard.
f) Battery packs or power tools must not be exposed to a fire or
excessive heat. Exposure to fire or a temperature exceeding 130°C may
result in an explosion.
g) It is necessary to adhere to all battery charging instructions
and not to charge the battery pack or power tool outside the
temperature range specified in this user's manual.
Incorrect charging, or charging at temperatures outside the specified
range may damage the battery and increase the risk of fire.
6) SERVICE
a) Have your cordless power tool repaired by a qualified person
using identical spare parts. This will ensure that the same level of
safety will be achieved as before the repair of the power tool.
b) Damaged battery packs must never be repaired. The battery
pack should only be repaired by the manufacturer or at an authorised
service centre.
XI. Maintenance and Repair
•
ATTENTION
y Pull the charger connector out of the cordless screwdriver before cleaning
and maintenance
y Keep the cordless screwdriver motor ventilation openings clean. Blocked
ventilation openings prevent air circulation into the motor, which prevents
proper cooling.
y For cleaning the power tool, use a damp cloth dipped in a detergent soluti-
on, prevent water from entering the power tool. Do not use any aggressive
cleaning agents and solvents. This would result in damage to the out plastic
housing of the power tool.
y For safety reasons, only use original parts from the manufacturer.
y In the event of a complaint, please contact the vendor from whom you
purchased the power tool or also contact the authorised service centre for
the Extol brand (service locations can be found at the website at the start
of the manual).
y Repairs of the power tool may only be performed by an authorised service
centre for the Extol® brand.
XII. Storage
y Store the cleaned tool in a safe location that is out of reach of children where
temperatures do not exceed 45°. Protect the tool against direct sunlight and
sources of radiant heat.
XIII. Waste disposal
y Throw the product packaging into a container for the respective sorted
waste.
y The product contains electronic components and therefore according
to the European Directive 2012/19 EU, it must not be
thrown out with household waste, but must be taken to
collection locations for environmentally safe waste dispo-
sal. Prior to disposing of the cordless screwdriver, remove
the built-in Li-ion battery by removing the handle. However, do not open the
battery. According to Directive 2006/66 EU, batteries must not be thrown out
with household waste, but taken to battery collection facilities for ecological
recycling because they contain environmentally hazardous contents.
You can find information about collection points at your local town council
office.
EU and GS Declaration of Conformity
Manufacturer: Madal Bal a.s. Bartošova 40/3, CZ-760 01 Zlín
Company ID No.: 49433717
hereby declares that the device designated below, based on its concept and
design, as well as designs sold on the market, complies with applicable safety
requirements of the European Union. This declaration becomes void in the event
of modifications to the product that are not approved by us. This declaration is
issued under the exclusive responsibility of the manufacturer.
Extol® Craft 402114
Cordless Screwdriver 3.6 V DC Li-ion, 1 500 mAh with flashlight
has been designed and manufactured in conformity with the following norms:
EN 62841-1:2015; EN 62841-2-2:2014; EN 60335-2-29:2004+A2;
EN 62233:2008; EN 55014-1:2017; EN 55014-2:2015;
EN 61000-3-2:2014; EN 61000-3-3:2013; EN 50581:2012; AfPS GS 2014:01
and regulations:
2006/42 ES (cordless screwdriver)
2014/35 EU (charger)
2011/65 EU (cordless screwdriver and charger)
2014/30 EU (cordless screwdriver and charger)
2009/125 ES (LED diodes cordless screwdriver)
The 2006/42 ES Technical Documentation has been drawn up by Martin Šenkýř
with headquarters at the address of the manufacturer. The technical documen-
tation (2006/42 ES) is available at the address of the manufacturer:
Place and date of issue of EU Declaration of Conformity: Zlín 5.5.2016
Person authorised to write up the EU Declaration of Conformity on behalf of the
manufacturer
(signature, name, function):
Martin Šenkýř, Member of the Board of Directors
- 4 -