Seite 1 METAL CHICKEN COOP MODEL:CRC0301...
Seite 2 This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
Seite 3: Safety Instructions
SAFETY INSTRUCTIONS WARNING: Read this material before using this product. Failure to do so can result in serious injury. Assembly precautions Assemble only according to these instructions. Improper assembly can create hazards. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
Seite 4: Parts List
TOOLS PARTS LIST - 3 -...
Seite 5 PARTS LIST - 4 -...
Seite 6: Exploded View
EXPLODED VIEW - 5 -...
Seite 7 ASSEMBLY STEP1 - 6 -...
Seite 8 STEP2 ▉ Note There are two pairs of holes on the vertical joint of Part C. When connecting Part 3 to Part C, make sure that the Button Clip is pointing to the left and right, like what’s shown on the left. - 7 -...
Seite 9 STEP3 - 8 -...
Seite 10 STEP4 - 9 -...
Seite 11 STEP5 - 10 -...
Seite 12 STEP6 ▉ Note DoDo not worry too much about the exact location of D3 and D6. Just make sure D6 is completely covered by the two pairs of H. Notice that on the two detailed illustrations above, screw L is not used. This is so that you have some wiggle room adjusting D3 and D6.
Seite 13 STEP7 - 12 -...
Seite 14 STEP8 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note In the package you will find the poultry net with a width of 1 meter (39 inches).
Seite 15 STEP9 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note For the net placed at the back of the chicken run, we suggest rolling the net roll without measuring or precutting the net like last step.
Seite 16 STEP10 Wire ▉ Note Spiral wrap the wire at the bottom to reinforce the wire mesh and steel pipe, with a distance of 15cm between each circle. The single wire should not be wrapped more than 2 meters, and it needs to be tightened during wrapping.
Seite 17 STEP11 The Cover/Tarp J is secured onto the structure using bungee ball O. Use one bungee ball per grommet on the tarp. Notice that, at the four corners, use two bungee balls for one grommet. - 16 -...
Seite 18 STEP12 ▉ Note When you feel like you have chosen a perfect spot for your chicken run and do not plan to move it, you can fasten it to the ground using the anchor M. Use one M per ground joint, like C, D, E, and P. - 17 -...
Seite 19 PRODUCT PARAMETER CRC0301 Model Colour Silver+Grey+White Product Size 3000×1000×2000mm Material Q235+PE Cloth NOTICE Site planning and selection Choose areas with high terrain and good drainage to avoid metal parts rusting due to water accumulation during the rainy season; Level the site in...
Seite 20 Manufacturer: Shanghaimuxinmuyeyouxiangongsi Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX E-CrossStu GmbH...
Seite 21 POULAILLER EN MÉTAL MODÈLE : CRC0301...
Seite 22 Ceci est le mode d'emploi d'origine. Veuillez lire attentivement l'intégralité du manuel avant utilisation. VEVOR se réserve le droit d'interpréter clairement ce manuel d'utilisation. L'apparence du produit dépend du produit que vous avez reçu. Veuillez nous excuser pour les éventuelles mises à...
Seite 23: Safety Instructions
SAFETY INSTRUCTIONS AVERTISSEMENT: Veuillez lire attentivement ce document avant d'utiliser ce produit. Le non-respect de ces instructions peut entraîner des blessures graves. Précautions de montage Assemblez uniquement conformément à ces instructions. Un assemblage incorrect peut créer des dangers. Portez des lunettes de sécurité approuvées ANSI et des gants de travail robustes pendant l’assemblage.
Seite 24: Parts List
CONSERVEZ CE MANUEL TOOLS PARTS LIST - 3 -...
Seite 25 PARTS LIST - 4 -...
Seite 26: Exploded View
EXPLODED VIEW - 5 -...
Seite 27 ASSEMBLY ÉTAPE 1 - 6 -...
Seite 28 ÉTAPE 2 - 7 -...
Seite 29 ▉ Note There are two pairs of holes on the vertical joint of Part C. When connecting Part 3 to Part C, make sure that the Button Clip is pointing to the left and right, like what’s shown on the left. ÉTAPE 3 - 8 -...
Seite 30 ÉTAPE 4 - 9 -...
Seite 31 ÉTAP - 10 -...
Seite 32 ÉTAP ▉ Note DoDo not worry too much about the exact location of D3 and D6. Just make sure D6 is completely covered by the two pairs of H. Notice that on the two detailed illustrations above, screw L is not used. This is so that you have some wiggle room adjusting D3 and D6.
Seite 33 ÉTAPE 7 - 12 -...
Seite 34 ÉTAPE 8 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note In the package you will find the poultry net with a width of 1 meter (39 inches).
Seite 35 ÉTAPE 9 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note For the net placed at the back of the chicken run, we suggest rolling the net roll without measuring or precutting the net like last step.
Seite 36 ÉTAPE 10 ▉ Note Spiral wrap the wire at the bottom to reinforce the wire mesh and steel pipe, with a distance of 15cm between each circle. The single wire should not be wrapped more than 2 meters, and it needs to be tightened during wrapping.
Seite 37 ÉTAPE 11 The Cover/Tarp J is secured onto the structure using bungee ball O. Use one bungee ball per grommet on the tarp. Notice that, at the four corners, use two bungee balls for one grommet. - 16 -...
Seite 38 ÉTAPE 12 ▉ Note When you feel like you have chosen a perfect spot for your chicken run and do not plan to move it, you can fasten it to the ground using the anchor M. Use one M per ground joint, like C, D, E, and P. - 17 -...
Seite 39 PARAMÈTRE DU PRODUIT CRC0301 Modèle Couleur Argent + Gris + Blanc Taille du produit 3000 × 1000 × 2000 mm Matériel Tissu Q235+PE AVIS Planification et sélection du site Choisissez des zones avec un terrain élevé et un bon drainage pour éviter la rouille des pièces métalliques due à...
Seite 40 vie du poulailler. Fabricant : Shanghaimuxinmuyeyouxiangongsi Adresse : Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, Shanghai 200 000 CN. Importé en Australie : SIHAO PTY LTD. 1 ROKEVA STREET, ASTWOOD NSW 2122 Australie Importé aux États-Unis : Sanven Technology Ltd. Suite 250, 9166 Anaheim Lieu, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED.
Seite 41 - 20 -...
Seite 42 HÜHNERSTALL AUS METALL MODELL: CRC0301...
Seite 43 Dies ist die Originalanleitung. Bitte lesen Sie alle Anweisungen sorgfältig durch, bevor Sie das Gerät in Betrieb nehmen. VEVOR behält sich eine klare Auslegung unserer Bedienungsanleitung vor. Das Aussehen des Produkts hängt vom gelieferten Produkt ab. Bitte haben Sie Verständnis dafür, dass wir Sie nicht erneut über Technologie- oder Software-Updates...
Seite 44: Safety Instructions
SAFETY INSTRUCTIONS WARNUNG: Lesen Sie dieses Material, bevor Sie dieses Produkt verwenden. Andernfalls kann es zu schweren Verletzungen kommen. Vorsichtsmaßnahmen bei der Montage Führen Sie die Montage ausschließlich gemäß dieser Anleitung durch. Eine unsachgemäße Montage kann zu Gefahren führen. Tragen Sie während der Montage eine ANSI-zugelassene Schutzbrille und strapazierfähige Arbeitshandschuhe.
Seite 45: Bewahren Sie Dieses Handbuch Auf
BEWAHREN SIE DIESES HANDBUCH AUF TOOLS PARTS LIST - 3 -...
Seite 46 PARTS LIST - 4 -...
Seite 47: Exploded View
EXPLODED VIEW - 5 -...
Seite 48 ASSEMBLY SCHRIT - 6 -...
Seite 49 SCHRITT 2 - 7 -...
Seite 50 ▉ Note There are two pairs of holes on the vertical joint of Part C. When connecting Part 3 to Part C, make sure that the Button Clip is pointing to the left and right, like what’s shown on the left. SCHRITT 3 - 8 -...
Seite 51 SCHRITT 4 - 9 -...
Seite 52 SCHRI TT 5 - 10 -...
Seite 53 SCHRI TT 6 ▉ Note DoDo not worry too much about the exact location of D3 and D6. Just make sure D6 is completely covered by the two pairs of H. Notice that on the two detailed illustrations above, screw L is not used. This is so that you have some wiggle room adjusting D3 and D6.
Seite 54 STEP7 - 12 -...
Seite 55 SCHRITT 8 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note In the package you will find the poultry net with a width of 1 meter (39 inches).
Seite 56 SCHRITT 9 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note For the net placed at the back of the chicken run, we suggest rolling the net roll without measuring or precutting the net like last step.
Seite 57 SCHRITT 10 Drah ▉ Note Spiral wrap the wire at the bottom to reinforce the wire mesh and steel pipe, with a distance of 15cm between each circle. The single wire should not be wrapped more than 2 meters, and it needs to be tightened during wrapping.
Seite 58 SCHRITT 11 The Cover/Tarp J is secured onto the structure using bungee ball O. Use one bungee ball per grommet on the tarp. Notice that, at the four corners, use two bungee balls for one grommet. - 16 -...
Seite 59 SCHRITT 12 ▉ Note When you feel like you have chosen a perfect spot for your chicken run and do not plan to move it, you can fasten it to the ground using the anchor M. Use one M per ground joint, like C, D, E, and P. - 17 -...
Seite 60 PRODUKTPARAMETER SFB 0301 Modell Farbe Silber + Grau + Weiß Produktgröße 3000×1000×2000mm Material Q235+PE-Gewebe BEACHTEN Standortplanung und -auswahl Wählen Sie Gebiete mit hohem Gelände und guter Drainage, um zu vermeiden, dass Metallteile durch Wasseransammlungen während der Regenzeit rosten. Einebnen Sie den Standort im Voraus, entfernen Sie Steine, Unkraut und anderen Schutt und legen Sie bei Bedarf Betonfundamente (insbesondere bei großen Hühnerställen aus Metall), um die Stabilität zu verbessern.
Seite 61 Lockerheit und beheben Sie auftretende Probleme umgehend, um die Lebensdauer des Hühnerstalls zu verlängern. Hersteller: Shanghaimuxinmuyeyouxiangongsi Adresse: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, Shanghai 200000 CN. Importiert nach AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australien Importiert in die USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED.
Seite 62 - 20 -...
Seite 63 METALOWY KURNIK MODEL: CRC0301...
Seite 64 QR code20250826\ To jest oryginalna instrukcja obsługi. Przed użyciem prosimy o dokładne zapoznanie się z treścią instrukcji. Firma VEVOR zastrzega sobie prawo do jednoznacznej interpretacji niniejszej instrukcji obsługi. Wygląd produktu zależy od stanu, w jakim go otrzymali Państwo. Prosimy o wyrozumiałość, ale nie będziemy Państwa ponownie informować...
Seite 65: Safety Instructions
SAFETY INSTRUCTIONS OSTRZEŻENIE: Przeczytaj ten materiał przed użyciem produktu. Nieprzestrzeganie tego zalecenia może spowodować poważne obrażenia. Środki ostrożności podczas montażu Montaż należy wykonywać wyłącznie zgodnie z niniejszą instrukcją. Nieprawidłowy montaż może stwarzać zagrożenie. Podczas montażu należy nosić okulary ochronne zatwierdzone przez ANSI oraz wytrzymałe rękawice robocze.
Seite 66: Parts List
ZAPISZ TĘ INSTRUKCJĘ TOOLS PARTS LIST - 3 -...
Seite 67 PARTS LIST - 4 -...
Seite 68: Exploded View
EXPLODED VIEW - 5 -...
Seite 69 ASSEMBLY KROK 1 - 6 -...
Seite 70 KROK 2 - 7 -...
Seite 71 ▉ Note There are two pairs of holes on the vertical joint of Part C. When connecting Part 3 to Part C, make sure that the Button Clip is pointing to the left and right, like what’s shown on the left. KROK 3 - 8 -...
Seite 72 KROK 4 - 9 -...
Seite 73 KROK - 10 -...
Seite 74 KROK ▉ Note DoDo not worry too much about the exact location of D3 and D6. Just make sure D6 is completely covered by the two pairs of H. Notice that on the two detailed illustrations above, screw L is not used. This is so that you have some wiggle room adjusting D3 and D6.
Seite 75 KROK 7 - 12 -...
Seite 76 KROK 8 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note In the package you will find the poultry net with a width of 1 meter (39 inches).
Seite 77 KROK 9 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note For the net placed at the back of the chicken run, we suggest rolling the net roll without measuring or precutting the net like last step.
Seite 78 KROK 10 Drut ▉ Note Spiral wrap the wire at the bottom to reinforce the wire mesh and steel pipe, with a distance of 15cm between each circle. The single wire should not be wrapped more than 2 meters, and it needs to be tightened during wrapping.
Seite 79 KROK 11 The Cover/Tarp J is secured onto the structure using bungee ball O. Use one bungee ball per grommet on the tarp. Notice that, at the four corners, use two bungee balls for one grommet. - 16 -...
Seite 80 KROK 12 ▉ Note When you feel like you have chosen a perfect spot for your chicken run and do not plan to move it, you can fasten it to the ground using the anchor M. Use one M per ground joint, like C, D, E, and P. - 17 -...
Seite 81 PARAMETR PRODUKTU CRC0301 Model Kolor Srebrny+Szary+Biały Rozmiar produktu 3000×1000×2000 mm Tworzywo Tkanina Q235+PE OGŁOSZENIE Planowanie i wybór lokalizacji Wybierz teren z wysokim terenem i dobrym drenażem, aby uniknąć rdzewienia elementów metalowych z powodu gromadzenia się wody w porze deszczowej. Wypoziomuj teren wcześniej, usuń kamienie, chwasty i inne zanieczyszczenia, a w razie potrzeby połóż...
Seite 82 wiązań siatek i niezwłocznie rozwiązuj wszelkie wykryte problemy, aby wydłużyć żywotność kurnika. Producent: Shanghaimuxinmuyeyouxiangongsi Adres: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, szanghaj 200000 CN. Importowane do AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Importowane do USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Miejsce, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED.
Seite 83 - 20 -...
Seite 84 METALEN KIPPENHOK MODEL: CRC0301...
Seite 85 Dit is de originele handleiding. Lees alle instructies zorgvuldig door voordat u het product gebruikt. VEVOR behoudt zich het recht voor om de gebruiksaanwijzing duidelijk te interpreteren. Het uiterlijk van het product is afhankelijk van het product dat u hebt ontvangen. Neemt u het ons niet kwalijk dat we u niet meer op de hoogte stellen van eventuele technologische of software-updates voor ons product.
Seite 86: Safety Instructions
SAFETY INSTRUCTIONS WAARSCHUWING: Lees dit materiaal voordat u dit product gebruikt. Het niet naleven hiervan kan ernstig letsel tot gevolg hebben. Voorzorgsmaatregelen voor montage Monteer uitsluitend volgens deze instructies. Onjuiste montage kan gevaarlijk zijn. Draag tijdens de montage een ANSI-goedgekeurde veiligheidsbril en stevige werkhandschoenen.
Seite 87: Parts List
TOOLS PARTS LIST - 3 -...
Seite 88 PARTS LIST - 4 -...
Seite 89: Exploded View
EXPLODED VIEW - 5 -...
Seite 90 ASSEMBLY STAP 1 - 6 -...
Seite 91 STAP 2 - 7 -...
Seite 92 ▉ Note There are two pairs of holes on the vertical joint of Part C. When connecting Part 3 to Part C, make sure that the Button Clip is pointing to the left and right, like what’s shown on the left. STAP 3 - 8 -...
Seite 93 STAP 4 - 9 -...
Seite 94 STAP - 10 -...
Seite 95 STAP ▉ Note DoDo not worry too much about the exact location of D3 and D6. Just make sure D6 is completely covered by the two pairs of H. Notice that on the two detailed illustrations above, screw L is not used. This is so that you have some wiggle room adjusting D3 and D6.
Seite 96 STAP 7 - 12 -...
Seite 97 STAP 8 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note In the package you will find the poultry net with a width of 1 meter (39 inches).
Seite 98 STAP 9 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note For the net placed at the back of the chicken run, we suggest rolling the net roll without measuring or precutting the net like last step.
Seite 99 STAP 10 Draa ▉ Note Spiral wrap the wire at the bottom to reinforce the wire mesh and steel pipe, with a distance of 15cm between each circle. The single wire should not be wrapped more than 2 meters, and it needs to be tightened during wrapping.
Seite 100 STAP 11 The Cover/Tarp J is secured onto the structure using bungee ball O. Use one bungee ball per grommet on the tarp. Notice that, at the four corners, use two bungee balls for one grommet. - 16 -...
Seite 101 STAP 12 ▉ Note When you feel like you have chosen a perfect spot for your chicken run and do not plan to move it, you can fasten it to the ground using the anchor M. Use one M per ground joint, like C, D, E, and P. - 17 -...
Seite 102 PRODUCTPARAMETER CRC0301 Model Kleur Zilver+Grijs+Wit Productgrootte 3000×1000×2000mm Materiaal Q235+PE-doek KENNISGEVING Locatieplanning en -selectie Kies gebieden met een hoog terrein en goede drainage om te voorkomen dat metalen onderdelen roesten door waterophoping tijdens het regenseizoen. Egaliseer de locatie van tevoren, verwijder stenen, onkruid en ander afval en leg indien nodig een fundering van beton (met name bij grote metalen kippenhokken) om de stabiliteit te verbeteren.
Seite 103 Fabrikant: Shanghaimuxinmuyeyouxiangongsi Adres: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. Geïmporteerd naar AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australië Geïmporteerd naar de VS: Sanven Technology Ltd. Suite 250, 9166 Anaheim Plaats, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX E-CrossStu GmbH...
Seite 104 - 20 -...
Seite 105 HÖNSHUS I METALL MODELL: CRC0301...
Seite 106 Detta är originalinstruktionerna, vänligen läs alla instruktioner noggrant innan du använder produkten. VEVOR förbehåller sig en tydlig tolkning av vår användarmanual. Produktens utseende ska vara beroende av den produkt du mottagit. Vi ber om ursäkt för att vi inte kommer att informera dig igen om det finns några teknik- eller programuppdateringar för vår...
Seite 107: Safety Instructions
SAFETY INSTRUCTIONS VARNING: Läs detta material innan du använder produkten. Underlåtenhet att göra det kan leda till allvarliga skador. Monteringsförsiktighetsåtgärder Montera endast enligt dessa instruktioner. Felaktig montering kan skapa risker. Använd ANSI-godkända skyddsglasögon och kraftiga arbetshandskar under monteringen. Håll samlingsområdet rent och väl upplyst. Håll åskådare borta från området under monteringen.
Seite 108: Parts List
TOOLS PARTS LIST - 3 -...
Seite 109 PARTS LIST - 4 -...
Seite 110: Exploded View
EXPLODED VIEW - 5 -...
Seite 111 ASSEMBLY STEG1 - 6 -...
Seite 112 STEG2 ▉ Note There are two pairs of holes on the vertical joint of Part C. When connecting Part 3 to Part C, make sure that the Button Clip is pointing to the left and right, like what’s shown on the left. - 7 -...
Seite 113 STEG3 - 8 -...
Seite 114 STEG4 - 9 -...
Seite 115 STEG - 10 -...
Seite 116 STEG ▉ Note DoDo not worry too much about the exact location of D3 and D6. Just make sure D6 is completely covered by the two pairs of H. Notice that on the two detailed illustrations above, screw L is not used. This is so that you have some wiggle room adjusting D3 and D6.
Seite 117 STEG7 - 12 -...
Seite 118 STEG8 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note In the package you will find the poultry net with a width of 1 meter (39 inches).
Seite 119 STEG9 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note For the net placed at the back of the chicken run, we suggest rolling the net roll without measuring or precutting the net like last step.
Seite 120 STEG10 Trå ▉ Note Spiral wrap the wire at the bottom to reinforce the wire mesh and steel pipe, with a distance of 15cm between each circle. The single wire should not be wrapped more than 2 meters, and it needs to be tightened during wrapping.
Seite 121 STEG11 The Cover/Tarp J is secured onto the structure using bungee ball O. Use one bungee ball per grommet on the tarp. Notice that, at the four corners, use two bungee balls for one grommet. - 16 -...
Seite 122 STEG12 ▉ Note When you feel like you have chosen a perfect spot for your chicken run and do not plan to move it, you can fasten it to the ground using the anchor M. Use one M per ground joint, like C, D, E, and P. - 17 -...
Seite 123 PRODUKTPARAMETER CRC0301 Modell Färg Silver+Grå+Vit Produktstorlek 3000×1000×2000 mm Material Q235+PE-tyg VARSEL Platsplanering och val Välj områden med hög terräng och bra dränering för att undvika att metalldelar rostar på grund av vattenansamling under regnperioden; Jämna ut platsen i förväg, ta bort stenar, ogräs och annat skräp, och lägg vid behov betongfundament (särskilt för stora hönshus i metall) för att...
Seite 124 Tillverkare: Shanghaimuxinmuyeyouxiangongsi Adress: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, Shanghai 200 000 kanadensiska republiken. Importerad till Australien: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australien Importerad till USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Plats, Rancho Cucamonga, Kalifornien 91730 YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX E-CrossStu GmbH...
Seite 125 - 20 -...
Seite 126 GALLINERO DE METAL MODELO: CRC0301...
Seite 127 Estas son las instrucciones originales; lea atentamente todas las instrucciones del manual antes de utilizarlo. VEVOR se reserva el derecho de interpretar su manual de usuario. La apariencia del producto dependerá del producto que haya recibido. Le rogamos que nos disculpe si no le informamos de nuevo si hay actualizaciones tecnológicas o de software en...
Seite 128: Safety Instructions
SAFETY INSTRUCTIONS ADVERTENCIA: Lea este material antes de usar este producto. De lo contrario, podría sufrir lesiones graves. Precauciones de montaje Ensamble únicamente según estas instrucciones. Un montaje incorrecto puede causar riesgos. Use gafas de seguridad aprobadas por ANSI y guantes de trabajo resistentes durante el montaje.
Seite 129: Parts List
GUARDE ESTE MANUAL TOOLS PARTS LIST - 3 -...
Seite 130 PARTS LIST - 4 -...
Seite 131: Exploded View
EXPLODED VIEW - 5 -...
Seite 132 ASSEMBLY PASO 1 - 6 -...
Seite 133 PASO 2 - 7 -...
Seite 134 ▉ Note There are two pairs of holes on the vertical joint of Part C. When connecting Part 3 to Part C, make sure that the Button Clip is pointing to the left and right, like what’s shown on the left. PASO 3 - 8 -...
Seite 135 PASO 4 - 9 -...
Seite 136 PASO - 10 -...
Seite 137 PASO ▉ Note DoDo not worry too much about the exact location of D3 and D6. Just make sure D6 is completely covered by the two pairs of H. Notice that on the two detailed illustrations above, screw L is not used. This is so that you have some wiggle room adjusting D3 and D6.
Seite 138 PASO 7 - 12 -...
Seite 139 PASO 8 norte Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note In the package you will find the poultry net with a width of 1 meter (39 inches).
Seite 140 PASO 9 norte Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note For the net placed at the back of the chicken run, we suggest rolling the net roll without measuring or precutting the net like last step.
Seite 141 PASO 10 Cabl ▉ Note Spiral wrap the wire at the bottom to reinforce the wire mesh and steel pipe, with a distance of 15cm between each circle. The single wire should not be wrapped more than 2 meters, and it needs to be tightened during wrapping.
Seite 142 PASO 11 The Cover/Tarp J is secured onto the structure using bungee ball O. Use one bungee ball per grommet on the tarp. Notice that, at the four corners, use two bungee balls for one grommet. - 16 -...
Seite 143 PASO 12 ▉ Note When you feel like you have chosen a perfect spot for your chicken run and do not plan to move it, you can fasten it to the ground using the anchor M. Use one M per ground joint, like C, D, E, and P. - 17 -...
Seite 144 PARÁMETRO DEL PRODUCTO CRC0301 Modelo Color Plata+Gris+Blanco Tamaño del producto 3000×1000×2000 mm Tela Q235+PE Material AVISO Planificación y selección del sitio Elija áreas con terreno alto y buen drenaje para evitar que las partes metálicas se oxiden debido a la acumulación de agua durante la temporada de lluvias;...
Seite 145 recubrimientos antioxidantes, inspeccione las ataduras de las redes para detectar posibles holguras y solucione cualquier problema de inmediato para prolongar la vida útil del gallinero. Fabricante: Shanghaimuxinmuyeyouxiangongsi Dirección: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, Shanghái 200000 CN. Importado a AUS: SIHAO PTY LTD. 1 ROKEVA STREET, EASTWOOD NSW 2122 Australia Importado a EE.
Seite 146 - 20 -...
Seite 147: Pollaio In Metallo
POLLAIO IN METALLO MODELLO: CRC0301...
Seite 148 Queste sono le istruzioni originali, si prega di leggere attentamente tutte le istruzioni del manuale prima dell'uso. VEVOR si riserva la piena interpretazione del proprio manuale utente. L'aspetto del prodotto dipenderà dal prodotto ricevuto. Vi preghiamo di scusarci se non vi informeremo più...
Seite 149 SAFETY INSTRUCTIONS AVVERTIMENTO: Leggere attentamente questo materiale prima di utilizzare il prodotto. La mancata osservanza di questa indicazione può causare gravi lesioni. Precauzioni di montaggio Montare solo secondo queste istruzioni. Un montaggio improprio può comportare pericoli. Durante il montaggio, indossare occhiali di sicurezza omologati ANSI e guanti da lavoro resistenti.
Seite 150: Parts List
CONSERVARE QUESTO MANUALE TOOLS PARTS LIST - 3 -...
Seite 151 PARTS LIST - 4 -...
Seite 152 EXPLODED VIEW - 5 -...
Seite 153 ASSEMBLY PASSO - 6 -...
Seite 154 PASSO 2 - 7 -...
Seite 155 ▉ Note There are two pairs of holes on the vertical joint of Part C. When connecting Part 3 to Part C, make sure that the Button Clip is pointing to the left and right, like what’s shown on the left. PASSO 3 - 8 -...
Seite 156 PASSO 4 - 9 -...
Seite 157 PASS - 10 -...
Seite 158 PASS ▉ Note DoDo not worry too much about the exact location of D3 and D6. Just make sure D6 is completely covered by the two pairs of H. Notice that on the two detailed illustrations above, screw L is not used. This is so that you have some wiggle room adjusting D3 and D6.
Seite 159 PASSO 7 - 12 -...
Seite 160 PASSO 8 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note In the package you will find the poultry net with a width of 1 meter (39 inches).
Seite 161 PASSO 9 Use zip ties to tie the wire mesh and steel pipes together, with an interval of 20cm between each tie. Tighten the wire mesh by lowering the zip ties ▉ Note For the net placed at the back of the chicken run, we suggest rolling the net roll without measuring or precutting the net like last step.
Seite 162 PASSO 10 Filo ▉ Note Spiral wrap the wire at the bottom to reinforce the wire mesh and steel pipe, with a distance of 15cm between each circle. The single wire should not be wrapped more than 2 meters, and it needs to be tightened during wrapping.
Seite 163 PASSO 11 The Cover/Tarp J is secured onto the structure using bungee ball O. Use one bungee ball per grommet on the tarp. Notice that, at the four corners, use two bungee balls for one grommet. - 16 -...
Seite 164 PASSO 12 ▉ Note When you feel like you have chosen a perfect spot for your chicken run and do not plan to move it, you can fasten it to the ground using the anchor M. Use one M per ground joint, like C, D, E, and P. - 17 -...
Seite 165 PARAMETRO DEL PRODOTTO CRC0301 Modello Colore Argento+Grigio+Bianco Dimensioni del 3000×1000×2000mm prodotto Materiale Tessuto Q235+PE AVVISO Pianificazione e selezione del sito Scegliere aree con terreno elevato e buon drenaggio per evitare che le parti metalliche arrugginiscano a causa dell'accumulo di acqua durante la stagione delle piogge;...
Seite 166 Produttore: Shanghaimuxinmuyeyouxiangongsi Indirizzo: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, Shanghai 200000 CN. Importato in AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD Nuovo Galles del Sud 2122 Australia Importato negli USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Luogo, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX E-CrossStu GmbH...
Seite 167 - 20 -...

VEVOR CRC0301 Bedienungsanleitung

Verfügbare Sprachen

Verwandte Anleitungen für VEVOR CRC0301

Inhaltszusammenfassung für VEVOR CRC0301

Inhaltsverzeichnis