Maintenance And Cleaning - Sygonix BLE Motion Tag Bedienungsanleitung

c) Key ring
• Attach the string of the key ring to the silicon case and attach the
other end to your bunch of keys.
• Slide the tag into the silicon case.
Operation
a) Installing the battery
1. Slide the cover (5) down.
2. Slide a button cell battery (4) of type CR2430 with (+) pole
facing down into the compartment as shown in the diagram in
chapter "Operating elements".
3. Mount the cover again. Make sure it locks.
• There is a low battery indicator in the app. When it shows, replace
the battery as described above.
b) Preparing your mobile device
1. Download the Sygonix app "Sensor Tag" from the Apple app
store or Google Play respectively.
2. Turn on Bluetooth.
3. Permit the app to use your mobile device's location services.
4. Turn on location services.
5. Turn on notifications.
c) Pairing
1. Open the app.
2. Press the button to register a new device.
3. Press <ADD SENSOR
4. Touch and hold the touch sensor (2) for approx. 2 sec.
5. Once the tag is recognized by the mobile device, name it and
add a picture if needed.
6. The pairing is complete.
d) How it works
In order to preserve battery power, the tag automatically goes into
sleep mode when not in use.
• After having paired the tag with your mobile device and
configured it, wake it up by touching the touch sensor (2). The
green operation indicator light (3) lights up briefly.
It is important that you follow the instructions given in the in-app
help menu in regards to the detection and setting up of events.
If the tag detects a registered event, it will push a notification for
this event to the Bluetooth address of every registered mobile
device. If a mobile device is out of range (>30 m) or turned off then
the notification will not be received on the mobile device. However,
every event is stored on the tag and can be retrieved through the
app when the mobile device is back in range.
Updating tag firmware
In order to ensure compatibility between app and tag, keep
both up-to-date at all times.
After installing an app update, always check if the tag firmware
needs to be updated as well. Tag firmware updates are
indicated in the app.
1. Make sure the battery has sufficient charge. Replace it by a
new one before the firmware update, if necessary.
2. Open the app.
3. Press > select tag > press
4. Press <Uploading Firmware
5. Press <START>. The red firmware update indicator light (3)
lights up and the firmware starts to update.
6. After updating you may use the tag again as usual.
Remark: In case the tag does not function properly after a
firmware update, remove and insert the battery again.
>.
.
>

Maintenance and cleaning

Do not use any aggressive cleaning agents, rubbing alcohol or
other chemical solutions as they can cause damage to the
housing and malfunctioning.
• Never submerge the product in water.
• To clean the product, a dry, soft and clean cloth is sufficient. Do
not apply too much pressure to the housing to prevent scratching.
• Remove the battery if you do not use the tag for longer periods
of time.
Declaration of Conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau,
hereby declare that this product conforms to the fundamental
requirements and the other relevant regulations of the directive
1999/5/EC.
The Declaration of Conformity for this product can be found at
www.conrad.com.
Disposal
a) Product
Electronic devices are recyclable waste and must not be
disposed of in the household waste.
At the end of its service life, dispose of the product
according to the relevant statutory regulations.
Remove any inserted batteries and dispose of them
separately from the product.
b) Batteries
You as the end user are required by law (Battery Ordinance) to
return all used batteries. Disposing of them in the household waste
is prohibited.
Contaminated batteries are labelled with this symbol to
indicate that disposal in the domestic waste is forbidden.
The designations for the heavy metals involved are: Cd =
Cadmium, Hg = Mercury, Pb = Lead (name on batteries,
e.g. below the trash icon on the left).
Used batteries can be returned to collection points in
your municipality, our stores or wherever batteries are
sold.
You thus fulfil your statutory obligations and contribute
to the protection of the environment.
Technical data
Power supply ............................. 3 V, 1 x CR2430 battery
Bluetooth version ..................... 4.0
Protection rating ....................... IP44
Operating systems .................... min. Android 4.4, min. iOS 8.1
Operating conditions ................ +0°C to +75 °C,
Storage conditions.................... -10 °C to +85 °C,
Dimensions (W x H x D) ............. 30 x 65 x 5 mm
Weight........................................ approx. 13 g (incl. battery)
Legal notice
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
(www.conrad.com). All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems require the prior
written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
10 – 90 % RH (non-condensing)
10 – 90% RH (non-condensing)
V3_0316_02_JH