Technical Data; Cleaning And Care - Sygonix 2377680 Bedienungsanleitung

7 Operation
7.1 Switch-on time "TIME"
■
Control how long the connected the load stays ON after the sensor
is triggered.
■
If new motion is detected during the switched-on time, the timer will
restart.
■
See section "Technical data, PIR sensor time delay".
■
Dial settings:
– Counter clockwise: decrease the duration.
– Clockwise: increase the duration.
7.2 Switching threshold "LUX"
■
You can adjust the switching threshold for different ambient light
levels.
– Counter clockwise: activates motion detection in darker condi-
tions.
– Clockwise: activates motion detection in brighter conditions.
8 Troubleshooting
Problem Possible causes
■
Connected load
Check the LUX setting, it should correspond to ambient light levels. E.g., if it
does not switch is set too high the sensor will not trigger in the dark.
ON. ■
Check the power supply is functioning correctly.
■
Check if the connected device (e.g., lamp) is functioning correctly.
■
Movements within the detection area are too rapid and are filtered out by the
electronic system to prevent switching errors.
■
Motion detection is The ambient temperature is too high.
not functioning cor- ■
There are obstructions preventing the sensor from detecting heat sources
rectly
(e.g., glass).
■
Check that if there are induction sources within detection area.
■
Observe the correct installation height. See section "Technical data" for fur-
ther information.
■
The connected load Constant movements are occurring within the detection area.
is always ON. ■
New movement is detected before the previous switch-ON time has elapsed.
Try setting a shorter time interval.

9 Cleaning and care

Important:
The product is generally maintenance-free. Any repair or maintenance work must be carried
out by a specialist.
Clean the product with a dry, fibre-free cloth.
NOTICE! Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
4
10 Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.

11 Technical data

Operating voltage .................................. 220 – 240 V/AC 50/60 Hz
Rated load .............................................. max. 1200 W resistive (e.g. incandescent lamp)
Power consumption ............................... 0.58 W (static)
PIR sensor activation ............................. 3 – 2000 lux (adjustable)
PIR sensor detection range ................... Small sensor: max. 6 m (<24 °C)
PIR sensor detection angle .................... Small sensor: 180°C
PIR sensor installation height ................ 1.8 – 2.5 m
Protection class ...................................... II
Operating humidity ................................. <93 % RH
Operating temperature ........................... -5 to +30 °C
Storage humidity .................................... <93 % RH
Storage temperature .............................. -20 to +40 °C
Dimensions (L x W x H) ......................... 116 x 76 x 63 mm
Weight (approx.) .................................... 150 g
115.8 mm
76 mm
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2377680_V1_0721_dh_mh_en
max. 600 W inductive (e.g. energy-saving lamp or LED)
0.68 W (active)
Large sensor: max. 12 m (<24 °C)
Large sensor: 360°