Seite 1
Please register your system on the website www.my-Solution-D.com, to be informed whenever updates are available! georg neumann gmbh · ollenhauerstr. 98 · 13403 berlin · germany tel +49 (0)30 / 41 77 24-0 · fax -50 · headoffice@neumann.com · www.neumann.com...
How-Pool entwickelt hat. Sicherheitshinweise Beschreibung Das Multi Channel Audio Interface Ethersound Das MCA-ES ist ein Multi Channel Audio Interface, das bis zu acht DMI-8 über Ethersound fernsteu- MCA-ES dient zur Fernsteuerung von acht DMI-8 über Ethersound sowie zur Konvertierung der di- ert und deren digitale Audiodaten in ein Ether- gitalen Audiodaten in ein Ethersound Netzwerk.
Seite 3
MCA-ES auf dieses externe Synchronisationssi- gnal automatisch. Liegt ein Ethersound Netzwerk WORD CLOCK am IN Port des MCA-ES an, so synchronisiert sich das Gerät darauf mit höchster Priorität. Liegt kein Anzeige, dass das MCA-ES am Ethersound Netz- Synchronisationssignal am BNC-Eingang und kein...
Seite 4
MCA-ES (ID=F), das die über den CON- TROL BUS angeschlossene DMI-8 steuert. In Die folgenden Schritte erläutern die erstmalige diesem Fall ist das MCA-ES ist der Master des Installation eines digitalen Mikrofonsystems, be- RS 485-Busses. stehend aus Mikrofon, Digitalem Mikrofon-Inter- face DMI-8, Multi Channel Audio Interface Ether- 2.
DMI-8 und Mikrofonen via Ethersound Betriebstemperaturbereich ....0 °C … +45 °C (MCA-ES ID=„F“) verbinden Sie den CONTROL Lagerungstemperaturbereich..–20 °C … +70 °C BUS des MCA-ES über Patchkabel mit den DMI-8 Feuchtebereich ....... max. 90 % rel. hum. (Kaskadierung). bei +20 °C Bei Steuerung der Geräte über USB (MCA-ES...
Zusatzerläuterungen einstellbar mit Kodierschalter 7.1 Entfernung von MCA-ES und DMI-8 an der Geräterückseite. Grundsätzlich wird der Einbau des MCA-ES und Stromversorgung ........DC 15 V der DMI-8 in einem Rack empfohlen. Damit sind Leistungsaufnahme ........< 6 VA auch sämtliche Verbindungsleitungen (BNC für Word Clock, Patch-Kabel für CONTROL BUS und...
Seite 7
Geräten (MCA-ES oder auf der Geräte-Rückseite, für jedes DMI-8). Gerät eine andere ID ! ID bei laufendem Betrieb geän- DMI bzw. MCA-ES muss nach einer dert. ID -Änderung neu eingeschaltet werden, danach RCS neu starten oder Befehl Options/DMI ausfüh- ren und Fenster wieder schliessen.
Ethersound and feeds their digital audio data The Multi Channel Audio Interface Ethersound into an Ethersound network. MCA-ES provides remote control for eight DMI-8 The most important features of the MCA-ES are as via Ethersound and feeds their digital audio data follows: into an Ethersound network.
Indicates a valid GN audio data stream from the DMI-8 to the MCA-ES. The indicator blinks while There are two ways to remote control the MCA-ES the connected DMI-8 is synchronized. It shines and the connected DMI-8 and microphones by the...
DMI-8 using the CONTROL BUS. In this case the stallation of a digital microphone system consist- MCA-ES runs as the master of the RS 485 bus. ing of the microphone, the Digital Microphone 2. The MCA-ES (ID=0..E) and the DMI-8 run as Interface DMI-8, the Multi Channel Audio Inter- slaves of the RS 485 bus.
Updating of fi rmware to an external word clock or AES11 signal, The fi rmware in the MCA-ES, in the DMI-8 and in if present, otherwise the internal the Neumann microphones is updatable. Updates word clock generator is activated.
The word clock generator is always active and feed into the BNC output. Con- necting the MCA-ES word clock output to the cor- responding input of the cascaded DMI-8 is abso- lutely necessary for their synchronization.
The RCS does not indicate that a The DMI was not switched on Do not start the RCS until the DMI DMI-8 is connected to the MCA-ES at the time when the RCS was has been switched on, or execute started.
Seite 15
Ethersound Audio Control DMI-8 (ID 0) WORD CLOCK CTL BUS GN 1 (RS 485) DMI-8 (ID 1) WORD CLOCK CTL BUS GN 2 (RS 485) DMI-8 (ID 2) WORD CLOCK CTL BUS GN 3 (RS 485) DMI-8 (ID 7) WORD CLOCK CTL BUS GN 8 (RS 485)
Seite 16
Limitation of Liability Declaration of Conformity Georg Neumann GmbH shall not be liable for consequences of an inappro- Georg Neumann GmbH hereby declares that this device conforms to priate use of the product not being in compliance with the technical allow- the applicable CE standards and regulations.