Hameg Instruments HD 148 Bedienungsanleitung Seite 22

PRINTER SET
1: KIND OF HARDCOPY
Four different printout types can be selected using the
SETUP +/- keys.
_ pRlNT ALL
SIGNAL+PARAMETER
- SIGNAL+GRATICULE
- SIGNAL ONLY
The factory setting
complete printout containing all relevant data is made.
The setting "SIGNAL
the manufacturer's
and the user can then use a stamp to add a different
logo or company address.
With the setting "SIGNAL + GRATICULE" , the entire
parameter field is left out on the printout.
waveform and the graticule are printed out.
In the setting "SIGNAL ONLY", only the waveform is
printed out.
2: SET BEEPER
In this mode, the SETUP +/— keys can be used to
enable or disable the audible key press acknowledg-
ment (when ON a beeper sounds each time a key is
pressed).
3: SET POWER REPORT
Use the SETUP +/— keys to activate/deactivate
automatic line voltage report function.
When this function
Graphic Printer is turned on the power-up and power-
down times (with date) are logged. Precise capture of
this information is only possible in those operating
modes that display the current time of day.
If a power loss should occur while the Graphic Printer
is switched on, this fact is also recorded.
4: SET XY-MODE
If this function has been enabled (switched
the SETUP +/— keys, then scope memory contents
that were captured in dual channel Yt mode are printed
out as an XY representation.
This function is useful when the scope has no XY
storage function or cannot signal to the printer that
data have been captured
H077).
In case of HM408 and HM1007 the oscilloscope's
setting (Yt or XY mode) determines the type ofprintout.
8 • ENGLISH
is PRINT ALL, meaning
+ PARAMETER" suppresses
logo ("HAMEG Instruments"),
Only the
is enabled (ON), each time the
ON) using
in that mode (HM208 with
5: SET DOT-JOIN
The Graphic Printer's automatic
be enabled
with the SETUP +/— keys.
For waveforms
you also want to print out as such, we recommend
setting this function ON. This also permits printout of
steep signal edges that have not been adequately
sampled by the scope's A/D converter.
that a
Conversely, when certain signals are printed out in XY
mode the dot-join
connecting
can be suppressed
6: SET STARTTIME
For setting the start time for ONLINE TIMER mode.
Besides the start time, the LCD display also shows a
cursor (' ' _ '
CURSOR > keys in the SETUP field can be used to
move the cursor. The SETUP +/— keys change the
programmed
7: SET STARTDATE
For setting the start date for ONLINE TIMER mode.
Besides the time interval, the LCD display also shows
a cursor _
CURSOR > keys in the SETUP field can be used to
the
move the cursor. The SETUP +/— keys change the
programmed
8: SET INTERVAL
This function is for setting the time interval (up to a
maximum
When the
printout is made; it is then followed by another printout
each time the programmed
The time interval can be set to any value between 1
minute and 24 hours. Entering a time interval of zero
hours and zero minutes disables the interval function, so
that only one printout is made (at the start time and date).
Besides the start date, the LCD display also shows a
cursor
CURSOR > keys in the SETUP field can be used to
move the cursor. The SETUP +/— keys change the
programmed
9: SET CLOCK
For setting the current time of day.
dot-join function can
(switched ON) or disabled
captured by the scope in Yt mode that
function can insert
lines. Such useless linear interpolations
by disabling this function.
beneath the digits. The CURSOR < and
start time.
beneath the digits. The CURSOR < and
time interval
of 24 hours) for ONLINE
start time and start date
time interval elapses.
beneath the digits. The CURSOR < and
start date.
Subject to change without notice
(switched OFF)
incorrect
TIMER mode.
are reached a