LK SmartComfort RTW Bedienungsanleitung Seite 5

ENG | Instruction Manual
CREATING USER PROGRAMS U1 AND U2
With U1 and U2 you can create your own program. The time step is 30
minutes. Each time a value or symbol blinks, you can make a choice
with the (+) or (-) keys. Once the choice is made press
next step. You can at any time cancel a setting by pressing
Select program mode P. Then select user program
keys. Press the edition key
ming starts 00:00 and ends 24:00.
blinks and the display shows 01. Select desired mode
or with (+) or (-). Press OK. In this example select
The time 00:00 blinks and the display shows 01A. With (+) or (-) you
set the time when the reduced temperature should start this day
e.g. 00:00. Press OK.
The time 00:30 will blink and the display shows 01b. With the (+)
or (-) keys you set the time when the reduced temperature should
finish, 06:00. Press OK. The temperature blinks. Set the desired
reduced temperature, 20 °C. Press
blinks and the display shows
press OK. In this example select
display shows 02A. With the (+) or (-) key you select the time when the
reduced temperature should start, 09:00. Press
The time 09:30 will blink and the display shows
keys you select the time when the reduced temperature should finish,
16:00. Press OK.
The temperature blinks. Select the desired reduced temperature 18°C
and press OK.
In this way further settings can be made. Max. settings a day are 5
periods.
When you are finished programming press the edition key
display will show Copy Yes.
Now you can choose to copy the day program just created to subse-
quent days. The program creation will always start with day 1=First day
of the week. Press OK and copy the program to the following day.
If you don't want to copy the program, change the choice
Copy no with the (+) or (-) keys and confirm your choice with the
You will now be invited to create a new program for the following day.
When you press OK on the last day 7, you will be invited to save your
program. The message SAVE
OK to save your program. Auto
are now shown on the display.
The program you now have created has comfort temperature from
06:00 – 09:00 and 16:00 – 24:00.
Reduced temperature
Reduced temperature
SERVICE MODE
The room temperature unit has a menu to change the parameters. In
order to enter this menu press and hold the edition key
seconds.
Note that the clock setting mode is first shown. Hold the
down until the service menu is displayed.
Now you can select a parameter with the navigation keys
. Modify the value with the (+) and (-) keys and press OK. To leave
the parameter menu, choose parameter
KEYBOARD'S LOCK FUNCTION
This function prevents unauthorized changes of your settings.
• To activate the keyboard's lock function, press and hold
5
OK
U1 with the (+) or (-)
to create a new program. The program-
OK.
02. Select the desired mode and
.The time 06:00 blinks and the
OK.
02b. With the (+) or (-)
Copy Yes
appears and the green LED blinks. Press
operating mode and user program
, 20 °C, 00:00 – 06:00
, 18 °C, 09:00 – 16:00
99 End and press OK.
• Repeat the same procedure to unlock the keyboard
to go to the
AIRING
.
If the room unit detects a sudden drop in temperature the unit will
disregard this for the next half hour. Decimal point and temperature
unit blink.
REMOTE CONTROL
By connecting a GSM modem to the room unit, it can be remote
.
controlled e.g. via mobile phone. Please, see No. 12 under Parame-
ters and Functions. It may take some time before the symbol appears.
If a temperature setting or the operating mode in the room unit is
changed, the remote control will be interrupted. Note! Only a voltage-
and potential-free contact is to be connected to the terminal block on
the back of the room unit.
TROUBLE SHOOTING
Note that when a temperature setting has been changed it will take hours
before the room temperature corresponds to the new setting due to
dimensions of the heating system and insulation of the house.
If the room temperature unit works but the room temperature is not in
accordance with the program:
• Check the time setting
• Check that the program step is not too short
• Check that the difference between comfort and reduced
temperature is not too high
Otherwise do the trouble shooting according to the list in the
LK 110/LK 120/LK 130 SmartControl Instruction Manual.
and the
ERROR CODES - SHOWN ON THE DISPLAY:
10 Internal error
11 Supply temperature sensor
12 Outdoor sensor
to
13 Reserve
OK key.
14 Room temperature unit, communication error
15 Reserve
50 Room temperature unit, room temperature sensor
U1
for 10
key
or
and
www.lkarmatur.com
simultaneously. will now appear on the display.