Roborock Saros 10 Bedienungsanleitung Seite 9

A11-5—Water Filter
A11-6—Dock Location Beacon
A11-7—Robot Refill Port
A11-8—Charging Contacts
A11-9—Status Indicator Light
• Breathing: Emptying/Mop
washing
• Red: Dock error
• Off: Powered off/Charging
A11-10—Cleaning Solution Cartridge
A11-11—Dust Bag Slot
A11-12—Dust Container Door
A11-13—Mop Washing Module
A11-13-1—High-Speed Maintenance
Brush
A11-13-2—Washing Strip
A11-13-3—Clean Water Dispensers
A11-13-4—Maintenance Brush Latch
A11-14—Suction Inlet
Empty Wash Fill Dock Auto
A12
(Back View)
A12-1—Power Cord Storage Slot
A12-2—Water Outlet
A12-3—Water Pipe Slot
A12-4—Power Port
A12-5—Cord Outlets
A12-6—Water Inlet
Note: Power cord can exit at either side.
Installation Accessories
A13
A13-1—Inlet Pipe (1/4" pipe) × 1
A13-2—Drainpipe (3/8" pipe) × 1
A13-3—Harness Tube × 1
A13-4—Tap Water Filter × 1
A13-5—1/4" Lock Plate × 5
A13-6—3/8" Lock Plate × 3
A13-7—Clean Water Three-Way Valve
(Gasket Pre-Installed) × 1
Refill and Drainage Pipes
A14
A14-1—Tap Water Supply
A14-2—Tap Water Filter
A14-3—Clean Water Three-Way Valve
A14-4—3/8" Square Elbow
A14-5—3/8" Lock Plate
A14-6—Harness Tube
A14-7—Drainpipe (3/8" pipe)
A14-8—Floor Drain or Sewer Pipe
A14-9—Power Cord
A14-10—1/4" Lock Plate
A14-11—1/4" Square Elbow
A14-12—Snap Ring
A14-13—Inlet Pipe (1/4" pipe)
Installation
B
Important Information
B1
B1-1— Tidy cords, hard or sharp objects
(such as nails and glass), and loose
items from the ground and move
any unstable, fragile, precious, or
dangerous items to prevent personal
injury or property damage due to
items becoming tangled in, struck
by, or knocked over by the robot.
009
B1-2— When using the robot in a raised
area (such as in a duplex apartment),
always use a physical security barrier
to prevent accidental falls that may
result in personal injury or property
damage.
Notes:
• When using the robot for the first time, follow it
throughout its whole cleaning route and watch for
potential problems. The robot will be able to clean by
itself in future uses.
• To prevent excessive buildup of dirt on the mop cloths,
floors should be vacuumed at least three times before
the first mopping cycle.
B2
Check the Installation
Environment
Before installation, check whether the
following requirements are met and identify
the water inlet, outlet, and placement
location for the dock in your home:
1. The water inlet pressure range should
be 0.1-0.4 MPa. If it exceeds 0.4 MPa, a
pressure-reducing valve should be installed.
2. The diameter of the drainpipe outlet
should be no less than 0.015 m (0.05 ft).
The height difference between the
highest point of the drainage pipe and
the floor surface where the dock is
placed should not exceed 1 m (3.28 ft),
preferably not exceed 0.5 m (1.64 ft).
3. The dock should be placed against a wall
on a hard, flat surface (wood/tile etc.) with
good WiFi coverage and a power outlet
or power strip nearby. Reserve a space of