Virutex ATIB280 Gebrauchsanweisung Seite 14

the power tool.
• It is strictly prohibited to modify cutting tools and
the use of accessories not designed for this power tool.
• When using the power tool, you must pay attention and
stay alert. Do not use the power tool if you feel tired or
are under the influence of anesthesia, alcohol, or drugs.
• Do not place your fingers on the switch button to avoid
unintentionally turning on the tool while it is in motion.
• When placing screws, ensure that all matching
components are securely fastened and reliable before
operating the power tool. The switch should be started
in a safe position, and the power tool should run for
30 seconds; it should be immediately stopped in case of
severe vibration or any other issue, and arrangements
should be made for maintenance.
1.3 SAFETY INSTRUCTIONS FOR USE AND
MAINTENANCE OF THE BATTERY AND CHARGER
Do not store the tool and battery cartridge
in locations where the temperature may reach or
exceed 45° C.
Do not incinerate the battery cartridge.
Do not expose battery cartridge to water
or rain.
• Only recharge with the manufacturer's specified
charger. Only recharge with the manufacturer's specified
charger. A charger which is suitable for one type of
battery cartridge can cause a fire risk on another type
of battery cartridge.
• Only use this power tool with the battery cartridge
specifically designed for this model. The use of other
types of battery cartridges may cause injury to the
operator and a fire risk.
• When the battery cartridge is not in use, keep it away
from metal objects, such as paper clips, coins, keys, nails,
screws or other small metal objects that can establish
contact from one terminal to the other. Shorting the
battery terminals may cause burns or a fire.
• Battery fluid may be spilled under extreme conditions;
avoid contact with this liquid. In case of accidental
contact, rinse thoroughly with water. If the liquid comes
into contact with your eyes, seek medical attention.
Battery fluid may cause irritation or burns.
• Do not use damaged or modified batteries. Damaged
or modified batteries can behave in an unpredictable
way and may cause injury to the operator and a fire risk.
• Avoid switching the device on accidentally. Make sure
14
the on/off switch is in the off position before inserting
the battery. Carrying the power tool with your finger
on the on/off switch or inserting the battery with the
switch in the on position can cause accidents.
• Do not open the batteries. You could damage the
circuits.
• Fumes may be aired if there is battery damage and
improper use. In this case, go to a well-ventilated location
and seek medical assistance, if necessary. Fumes cause
respiratory irritation.
• When the battery is defective, the liquid may leak and
come into contact with adjacent components. Check the
corresponding parts. Clean or replace them, if necessary.
• Protect the battery from heat, continued solar radiation
and fire. There is an explosion hazard.
Read all instructions and safety warnings.
• Protect the battery charger from rain and moisture.
Water entering the charger increases the risk of electric
shock.
• Do not charge other batteries. The battery charger is
only suitable for charging lithium-ion batteries within
the indicated voltage range. Otherwise, there is a fire
and explosion hazard.
• Keep the battery charger clean. Dirt can cause a risk
of electric shock.
• Always check the battery charger, its cable and plug
before using them. Do not use the charger if you see it
is damaged. Do not open the charger on your own. Have
it repaired by a qualified person who uses original spare
parts. Damaged chargers, cables and plugs increase the
risk of electric shocks.
• Do not use the battery charger on highly flammable
surfaces. For example, paper, textiles, etc., or in com-
bustible environments. A fire hazard exists from the
charger heating during the charging cycle.
2. SPECIFICATIONS
Battery voltage: 20 V
No-load speed
Speed one: 0-400 min
-1
Speed two: 0-1,500 min
Third speed: 0-2,500 min
Number of impacts (gear: 1 / 2 / 3):
0-1,800 / 0-2,700 / 0-3,300 min
Tool holder: 6.35 mm (1/4")
Weight: 1,23 kg
3. DESCRIPTION OF THE TOOL
The power tool is designed for loosening and
tightening fasteners (screws, nuts, etc.).
-1
-1
-1