Werbung
Verfügbare Sprachen
Verfügbare Sprachen
4. Press the volume button B
to set the volume of the drink.
q
5. Press the brew button B
for the device to start making your drink.
w
Volume adjustment for brew
You can change the amount of coffee by adjusting the default brewing time to suit your taste.
1. Press the volume button B
to set the volume of the drink.
q
2. The device will record your selection for next use.
3. After adjustment, press the brew button B
to start brewing.
w
4. The brewing process process can be cancelled by pressing it again.
Note: When the brew button B
is pressed, its LED may blink for a few seconds before brewing the coffee.
w
This is normal.
For the best taste, it's strongly recommended to brew a cup of hot water first.
Use with Nespresso capsules
1. Open the lever A
.
1
2. Pull out the adapter C
.
e
3. Change the current adapter for the Nespresso adapter.
4. Open the adapter cover lid C
.
u
5. Put the capsule into the adapter.
6. Insert the adapter C
into the device. Make sure you put it into the end, then close the lever A
e
7. Place a cup under the dispenser.
8. Press the power button B
to turn on the machine. (Wait 20-45 seconds until all lights stop blinking)
9
9. Press the volume button B
to select the desired cofffee volume.
q
10. Press the brew button B
for the device to start making your drink.
w
11. Lift the lever A
and pull out the adapter. Dispose the used capsule and wash the adapter.
1
Use with Dolce Gusto capsules
1. Open the lever A
.
1
2. Pull out the adapter C
.
r
3. Change the current adapter for the Dolce Gusto adapter.
4. Put the capsule into the adapter.
5. Insert the adapter C
into the device. Make sure you put it into the end, then close the lever A
r
6. Place a cup under the dispenser.
7. Press the power button B
to turn on the machine. (Wait 20-45 seconds until all lights stop blinking)
9
8. Press the volume button B
to select the desired cofffee volume.
q
9. Press the brew button B
for the device to start making your drink.
w
10. Lift the lever A
and pull out the adapter. Dispose the used capsule and wash the adapter.
1
Note: The capsule holder for the Dolce gusto bulges after brewing which can cause problems when trying to
remove it. When the machine meets such a situation, it can push the capsule pocket into the core again and
press it with the handle to solve the problem of operation, which is one of the characteristics of the capsule.
The machine stops after the capsule is extracted, but the coffee and milk powder liquid inside the capsule
are not finished, and there is still a little pressure inside the capsule. When the handle is opened, the internal
pressure of the capsule will make the capsule film recoil and bulge and cause the pocket to be difficult to
access. This is a normal phenomenon.
Use with E.S.E coffee pods
1. Open the lever A
.
1
2. Pull out the adapter C
.
t
3. Change the current adapter for the E.S.E adapter.
4. Put the E.S.E coffee pod into the adapter C
.
t
© Princess | Multi Capsule Coffee Maker
.
1
.
1
10
| 01.249454.01.001
5. Insert the adapter C
into the device. Make sure you put it into the end, then close the lever A
t
6. Place a cup under the dispenser.
7. Press the power button B
to turn on the machine. (Wait 20-45 seconds until all lights stop blinking)
9
8. Press the volume button B
to select the desired cofffee volume.
q
9. Press the brew button B
for the device to start making your drink.
w
10. Lift the lever A
and pull out the adapter. Dispose the used capsule and wash the adapter.
1
Use with coffee powder
1. Open the lever A
.
1
2. Pull out the adapter C
.
y
3. Change the current adapter for the Coffee Powder adapter.
4. Add coffee powder to the powder adapter C
y
power with the flat side of the powder spoon.
5. Insert the adapter C into the device. Make sure you put it into the end, then close the lever A
6. Place a cup under the dispenser.
7. Press the power button B
to turn on the machine. (Wait 20-45 seconds until all lights stop blinking)
9
8. Press the volume button B
to select the desired cofffee volume.
q
9. Press the brew button B
for the device to start making your drink.
w
10. Lift the lever A
and pull out the adapter. Dispose the used capsule and wash the adapter.
1
Standby mode
•
The device will be turned off after 15 inactive minutes. Press the power button to cancel the standby
mode.
•
To put the device in standby mode, hold the volume B
the light of the volume button turns off, it indicates standby mode. when the light of the brew button
turns of, it indicates pre-brewing.
CLEANING AND MAINTENANCE
Cleaning the device
•
Always clean the device after each use.
•
Before cleaning, unplug the appliance and wait for the appliance to cool down.
•
Never immerse the appliance in water or other liquids or place it in a dishwasher.
•
Never use aggressive chemical cleaning agents that can damage the appliance when cleaning the
appliance.
•
Never use any sharp or metal objects when cleaning the appliance.
Dry with a fresh and clean towel, cloth, or paper, and reassemble all parts. Clean the coffee outlet A
•
and inside the machine regularly with a damp cloth.
Clean mode function
1. Place a cup under the dispenser.
2. Hold the volume button B
and power button B
q
3. Press the volume button B
to start the cleaning process.
q
Decalcify the device
Decalcification must be done correctly to prevent damage. So it is essential to follow these instructions.
- Never clean the device with vinegar. This causes damage and makes your coffee taste bad.
1. Fill the water tank A
with water to the maximum level, mixed with decalcifying solution. Make sure the
3
solution is dissolved completely.
2. Make sure there is no capsule in the device.
3. Place a large bowl under the dispenser.
4. Press the Brew button B
to run decalcifying water through the device. Repeat for several times to run
w
User manual
1
using the powder spoon C
. Press down the coffee
i
.
1
and brew B
buttons for 3 seconds. When
q
w
for 3 seconds to enter Clean Mode.
9
11
.
5
Werbung
