Xavax FeelSafe Bedienungsanleitung Seite 14

• Removethe cover from the GSMadd-on modu e (9)
• OpentheSIMcardcompartment (3) by unscrewing t he screw
and removing the cover.
• Unlock the SIM card holder and insert the SIM card as shown
below The SIM card's contact surfaces must face inwards.
• Lock the SIM card holder.
• Close theSIMcardcompartment byattachingandscrewing on
the cover
Power supply
Note —Power supply
• The4 AAAbatteries in theGSMadd-onmoduleareonly
backup batteries
• Alwaysusethe powersupplyunitprovided to ensure that the
GSM add-on module functions uninterru
• Remove thecoverto openthe batterycompartment (5) Insert4
AAAbatteries Withthe correctpolarityand plugthe powersuppy
unit intothe powersocket ( 6)
• Close the batterycompartment byattachingand screwing on
the cover
• Whenreplacing the batteries, f ollow thesameprocedure and
thendispose of the old batteries according to ocalreguations
Note —Status LEDs
Thebattery(l) andconnection statusLEDs (2) nowlight up The
two LEDs g o out oncethe producthasestablished a connection
to the mobile network The connection status LED(2) will flash
aboutevery10 seconds to indicate that the connection is
functioningproperly
5.3 Installation
Note — Installation
Decide where the GSM add-on module unit should be installed
The installation location should be:
• Neara poweroutlet
• Easily accessible b ut hiddenfrom unauthorised persons
• Awayfrom doorsor windowsthroughwhichintruders could
easilyaccess t he centralsystem usingappropriate tools
• Awayfrom sources of extreme temperatures ( heaters, o vens,
etc ) and largemetalobjects(whichcaninterfere with wireless
transmission)
12
ted
location
• Theproductisintendedto be installedon a wa
• f necessary, getyourselfa suitable tool from a specialised d ealer
for wall-mounting
• Attachthe productusingthe mountingholeson the back(10)
5.4 Enrolling on the FeelSafealarm control unit
Tousethefunctionsof the GSM add-onmodue,youmust
enrollIt on the FeelSafe a armcontrolunit Todo so, proceed as
• Ensure that the alarm control unit is in STANDBY mode
• Enterthe4 di it PINand pressENTER
(8) and RESET(7) buttons on the GSMadd-on
module at the same time and hold them for about 3 seconds A
series of signaltonesfrom thea armcontrolindicates that the
enrol ment was SUCCeSSfUI
• Toexit enrolmentmode,press
• f youdo not hearanysignal t ones,repeat t he procedure
5.5 Building (security) code setting
n orderfor al components o f a FeelSafe a armsystem to properly
functionwith theexistinga armcontrolunit, thesecomponents
mustall havethesamebuildingcodeasdoesthealarmcontrolunit.
• A1 components a ndthe a armcontrolunit havea 4 pin jumper/
DIPswitchin the batterycompartment or undera separate cover
on the back
• Ensure that thejumpers I DIPswitches in the a armcontrolunit
and the GSM add-onmodulehaveexactly thesamesettings,or
theywill notfunction
Jumper for
HOUSE CODE
the building
4321
code (4)
DIP switch for
the building
code
6. Controlling the GSMadd-on module with the
smartphone app
• Onyourterminaldevice(smartphone, tablet,etc.),download
the "GSMSecurity" appfrom theApp
Goog e Playfor Android@
• Whenyoufirststarttheapp,entera 4-digitaccess codeand
repeatit to confirm
• Youare nowdirected to the settings for yourmaindevice (button
namein theapp: 'Building')
then press the Settings
on the alarmcontrolunit
Alarm control unit
Sensors
Defaultbuildingcode:
l: ON, 2: ON, 3: ON,
4: ON
* Jumper: O N= plugged
in, O F= unplugged
Remote control
Defaultbuildingcode1:
ON, 2: ON, 3: ON, 4: ON
AppStoreor from