Sharp HT-SBW53121 Bedienungsanleitung Seite 6

5
Box contents
• Soundbar
• Wireless subwoofer
• Remote control (inc. batteries)
• Power adapter
• 2 pin (type C) plug adapter
• 3 pin (type G) plug adapter
• EU AC power cable
• UK AC power cable
• HDMI cable
• Soundbar low feet (2 pcs)
• Soundbar wall-mount brackets (2 pcs)
• Soundbar wall-mount fixings
• User manual
• Warranty card
Controls
Soundbar
(Refer to 1 on page 1)
1. – Switch the system between ON and STANDBY.
2. – Select the source of audio (HDMI eARC/ARC, HDMI 1, HDMI 2,
USB, AUX IN, BT, OPTICAL).
3.
– Select Bluetooth mode. Press and hold to activate the pairing
function in Bluetooth mode or disconnect the existing paired
Bluetooth device.
4. – Press to mute or resume the sound.
Long press to mute or unmute the rear speakers (if purchased
separately).
5. – Reduce volume.
6. – Increase volume.
(Refer to 2 on page 1)
1. DC IN – Socket for connecting power adapter (DC 22V, 2.1A).
2. Optical – Optical input port.
3. AUX IN – Connect to an external audio device.
4. USB – Insert USB flash drive to play music.
5. HDMI (1/2/eARC/ARC) – Connect HDMI TV (eARC/ARC) to your
TVs HDMI (eARC/ARC) port. Connect other devices to HDMI 1 / 2 to
pass-through to TV.
Subwoofer
(Refer to 3 on page 1)
1. PAIR indicator.
2.
button – Please refer to section "Subwoofer pairing".
3. AC IN power input.
Remote Control
(Refer to 4 on page 1)
1.
– Switch the system between ON and STANDBY.
2. – Select the source of audio (HDMI eARC/ARC, HDMI 1, HDMI 2,
USB, AUX IN, BT, OPTICAL).
3. / – Menu navigation. Adjust setting value.
4.
/ - Press to skip to previous/next track or long press to fast
rewind/fast forward in Bluetooth/USB source. Menu navigation.
5.
– Play/pause/resume playback in Bluetooth/USB source. Menu
selection.
6. – Cycle EQ presets..
7.
– Enter the soundbar menu.
8.
– Press to mute or resume the sound.
Long press to mute or unmute the rear speakers (if purchased
separately).
9. / – Press to activate bass level adjustment in custom EQ
preset.
10. / – Press to activate treble level adjustment in custom
EQ preset.
11. / – Increase/decrease the volume level.
Battery installation
1. To open the battery compartment, push your thumb down on to the
battery compartment cover and slide it down.
2. Fit two AAA batteries observing polarity +/- as shown. When
replacing the batteries, use only the same type of battery supplied.
3. Re-fit the battery cover and clip it in place.
Soundbar front
(Refer to 5 on page 1)
1. Remote control sensor.
2. LED display.
Soundbar base
(Refer to 6 on page 2)
1. Wall-mount bracket screw locations.
Placement and mounting
Placement - soundbar
A If your TV is placed on a table or a wall, you can place the soundbar
on a flat surface in front of or underneath the TV, centred with the
TV screen.
B If your TV has a centre-mounted stand, you can consider to use the
pre-fitted high feet to elevate the soundbar over all or part of the
TV stand. This feature has been designed for use with Sharp EQ and
FQ series TVs and compatibility with other models and brands is not
guaranteed.
C If your TV is attached to a wall, you can mount the soundbar on the
wall directly below the TV screen, centred with the TV screen using
the included wall-mount kit.
Wall mounting (if using option-C)
(Refer to 7 on page 2)
• Installation must be carried out by qualified personnel only. Incorrect
assembly can result in severe personal injury and property damage
(if you intend to install this product yourself, you must check for
installations such as electrical wiring and plumbing that may be
buried inside the wall). It is the installer's responsibility to verify that
the wall will safely support the total load of the soundbar and wall
brackets.
• Install the Soundbar so the top of the soundbar is at least 100 mm
below the bottom of the TV.
• Additional tools (not included) are required for the installation.
• Do not overtighten screws.
• Keep this instruction manual for future reference.
• Use an electronic stud finder to check the wall type before drilling
and mounting.