GRAPHITE 59G614 Benutzerhandbuch Seite 7

• Inspection and maintenance should be carried out after the
electrically driven suction nozzle has been removed.
• Caution: the hose may become electrified.
• Do not trample or pull on the hose. A damaged hose should be
replaced before further work.
• Keep the squeegee at a safe distance during operation.
• Do not allow the power cable to come into contact with water, oil or
other liquids.
• Do not immerse the device in water, do not touch with wet hands, do
not use water for cleaning to avoid electric shock.
• Do not aspirate hair, glass, metal, sharp or sticky parts. This will
cause clogging or damage to the appliance components.
• Do not suck in flammable, hot, glowing or corrosive components,
cigarette butts, matches, etc., as this may cause a fire or electric
shock. - There is a risk of fire or electrical shock.
• The unit is not adapted and not suitable for extracting harmful dust.
• Do not use if the air intake is blocked or the bag is clogged as this
may damage the unit.
• When the device is not in use, remove the plug from the socket.
• Regularly check the technical condition of the unit. Replace
damaged or worn parts.
• Do not use the device if the cable is found to be damaged. Do not
touch the cable before disconnecting the power supply!
• If any damage is found or alarming signals such as excessive
temperature and noise are noticed, the unit should be switched off
immediately and unplugged.
• Protect from rain.
• Use only spare parts recommended by the manufacturer
• All repairs should be carried out at an authorised service centre.
EXPLANATION OF THE PICTOGRAMS USED
1.Note: Take special precautions.
2.Read the operating instructions, observe the warnings and safety
conditions contained therein.
3.Use personal protective equipment (safety goggles, hearing
protectors, dust masks)
4.Disconnect the power cable before servicing or repairing.
5.Protect from moisture.
6.Use the right tips for water extraction.
7.For interior use
8.Keep out of the reach of children
CONTENTS
• Suction hose
• Hoover
• Operating instructions
• Three-piece pipe
• Wheels
• Foam filter
• Canvas dust bag
• Suction tips
• Adapter
• Handle screws
• Screws for balls
APPLICATION
An all-purpose hoover designed for dry and wet work with the appropriate
filter.
DESCRIPTION OF THE GRAPHIC PAGES
1.Transport handle
2.O/I switch
3.Head
4.Filter basket
5.Float safety valve
6.Snaps
7.Tank
8.Suction hose connection
9.Blower connection
10.Suction hose
11.Wide nozzle
12.Foam filter
13.Slot nozzle
14. canvas dust bag
15.Three-part suction pipe
16.Wheels
17.Adapter (reducing adapter)
18. Hepa filter
MOUNTING THE BRACKET
Fasten the u-grip with two screws
INSTALLATION OF THE APPLIANCE HEAD
• The device head (3) is attached to the container (7) by means of the
locking latches (6).
• To remove the device head (3), open the locking latch (6) and
remove the device head (3).
• When assembling the appliance head (3), ensure that the locking
catch (6) is correctly locked.
FILTER INSTALLATION
• Never use the hoover without a suitable filter.
• For wet vacuuming work, slide the supplied foam filter (12) onto the
basket (4)
• For dry vacuuming A HEPA filter (18) is required, which is slid onto
the head (5) then a fabric dust bag (14) is slid onto the vacuum
opening. The fabric dust bag (14) is only suitable for dry vacuuming.
The cloth dust bag makes it easier to remove sucked dust, there is
a plastic zipper-like strip at the bottom of the dust bag, when the dust
bag is full, remove the dust bag from the vacuum opening, slide the
plastic strip to the side and remove the plastic strip, remove the dust
by throwing it into the dustbin and fit the plastic strip to the bottom of
the bag, then the dust bag can be reattached to the hoover tank
opening.
FITTING THE SUCTION HOSE
Connect the suction hose (10) to the appropriate hoover connector for
the job, depending on the required application.
CLEANING
Connect the suction hose (10) to the suction hose connector (8).
BLOWING
Connect the suction hose (10) to the blow-off connector (9).
SUCTION NOZZLES
• The wide nozzle (11) is used for vacuuming solids and liquids on
medium to large surfaces.
• The crevice nozzle (13) is specially designed for cleaning crevices
and edges.
ADAPTER
The included adapter (17) can be used to connect the suction hose
(10) to the power tool. To do this, mount it between the suction hose
and the hoover socket on the power tool.
The adaptor is compatible with most power tools that have a circular
waste ejection hole: sawdust, dust, etc.
1pc.
ON AND OFF
1pc.
Plug the plug into an outlet. Switch the switch (2) to position I to switch on
1pc.
the hoover. Switch the button to position 0 to switch off the hoover .
3pc.
4pc.
DRY VACUUMING
1pc.
For dry vacuuming, use a Hepa filter (18), and a cloth dust bag (14)
1pc.
WET VACUUMING
2pcs.
For wet vacuuming, use the foam filter (12)
1pc.
Always check that the filter is securely fastened.
2pc.
NOTE
4pc.
During wet vacuuming, the floating safety switch (5) closes when
the maximum level in the tank is reached. In this case, the suction
noise of the appliance will change and become louder.
The unit should then be switched off and the tank emptied.
Important!
The wet and dry hoover is not suitable for vacuuming flammable liquids.
Use only the foam filter provided for wet vacuuming.
NADMUCH
Connect the suction hose (10) to the blow-off connector (9) of the
hoover.
CLEANING, MAINTENANCE
NOTE
7