Cleaning And Maintenance - Rondell Rde-1009 Betriebsanweisung

– To switch the kettle OFF press and hold the control button
(6) « » for more than 3 seconds you will hear a short
sound signal and the kettle will be switched to stand-By
mode and shows the water temperature on the display. To
switch OFF completely press & hold the button (6) again
for more than 3 seconds after short sound signal display
indication will switched OFF, and kettle will be completely
switched OFF.
USING THE KETTLE AND ADDITIONAL FUNCTIONS
– Insert the power cord plug into the mains socket.
– To fill the kettle with water, remove it from the base (8), open
the lid (3) by pressing the lid opening button (4).
– Fill the kettle with water no higher than the maximum level
mark «MAX».
– Close the lid (3) and put the filled kettle on the base (8).
Make sure that the kettle lid (3) is closed tightly.
– To switch the kettle on, press the control button (6) «
twice, you will hear a short sound signal and the kettle will
enter standby mode, the digital symbols of the water tem-
perature in the kettle in °C will appear on the display (5).
Then you can choose the boiling water mode, or the heat-
ing water mode to the preset temperature and then keep-
ing it for 2 hours.
Note: if you did not press the control button (6) «
1 minute, the kettle will be switched off automatically and the
display indications will go out.
Boiling mode
– To boil water, press the control button (6) «
flashing 100° temperature digital symbols and the water
boiling indicator « » will appear on the display (5) for a
while. After some time (~ 5 sec.), the boiling process will
begin automatically, the digital symbols of the current
water heating temperature in the kettle in °C will appear on
the display (5).
– After the water boils, you will hear a long sound signal,
100 °C water temperature digital symbols will appear on the
display (5), the boiling process will stop, and after 1 minute
the display indications will go out, the kettle will be switched
off automatically.
Heating and keep warm modes
The kettle allows you to heat water up to 80, 70, 60 and 45 °C,
with subsequent 2-hours keeping the preset heating tem-
perature.
– To select the preset water heating temperature, press the
control button (6) « » sequentially, the flashing tempera-
ture digital symbols in °C and their corresponding heating
indicators will appear sequentially on the display (5) in the
following order: 80, 70, 60 and 45.
Note: the keep warm temperature mode is automatically acti-
vated when the water heating temperature is selected at 80,
70, 60 and 45 °C.
– Press the control button (6) «
the necessary temperature. After some time (~ 5 sec.), the
boiling process will begin automatically, the digital symbols
of the current water heating temperature in the kettle in °C
and the heating indicator of the preset temperature 80, 70,
60, or 45 will appear on the display (5).
– After the water in the kettle is heated to the preset tem-
perature, the heating process will stop, you will hear a long
sound signal, the preset water temperature digital symbols
in °C and the keep warm indicator «
display (5).
Note:
» – In the keep warm mode, the heating will be switched on
automatically when the temperature of the water in the ket-
tle decreases by more than 5 °C.
– In the keep warm mode, the digital symbols of set water
temperature in the kettle shown in °C, the keep warm indi-
cator « » and the corresponding heating indicator 80, 70,
60, or 45 constantly appear on the display (5).
» during
– When the kettle is removed from the base, the keep
warm mode is switched off automatically!
– To exit the keep warm mode, press and hold the control button
(6) « » for more than 2 seconds, the keep warm indicator
« » and the corresponding heating indicator will go out,
» once,
the kettle will enter standby mode.
– To switch the kettle OFF press and hold the control but-
ton (6) « » for more than 3 seconds you will hear a short
sound signal and the kettle will be switched to stand-By
mode and shows the water temperature on the display. To
switch OFF completely press & hold the button (6) again
for more than 3 seconds after short sound signal display
indication will switched OFF, and kettle will be completely
switched OFF

CLEANING AND MAINTENANCE

– Before cleaning disconnect the unit from the mains, pour
out water and let the kettle cool down.
– Wipe the outer surface of the kettle with a damp tissue or
a sponge. Use soft detergents to remove dirt; do not use
metal brushes and abrasive detergents.
– Keep the mesh filter clean and clean it from time to time.
To remove the mesh filter, open the kettle lid (3) and press
the upper part of the filter, then pull the filter up. Clean the
filter with a soft-pile brush and install it back to its place.
11
» sequentially to select
» will appear on the