Cleaning And Care - Rondell Rde-1005 Die Betriebsanweisung

(10, 11) will be switched on, and the temperature of the
water in the kettle will be shown on the display (6).
– To fill the kettle with water, remove it from the base (8).
The touch buttons (10, 11) illumination and the display
(6) will go out. Open the kettle lid (3) taking the lid by the
handle (4).
– Fill the kettle with water not over the maximum mark
«MAX», but not under the minimum mark «MIN».
– Close the lid (3) and put the full kettle on the base (8).
Make sure that the kettle lid (3) is closed tightly. You
will hear a sound signal and will see the backlight of the
touch buttons (10, 11), and the temperature of the water
in the kettle will be shown on the display (6).
Note: If no button is pressed, then the display (6) and the
backlight of the touch buttons (10, 11) will go out. To switch
the kettle on again, press the button
Boiling mode
– To boil water, press the button
process will begin, the temperature of the water will be
shown on the display (6), and you will also see the back-
light of the buttons (10, 11) and the flask of the kettle.
– After the water boils, you will hear three sound signals,
the boiling process will stop, the kettle flask backlight will
be switched off, after some time the display (6) and the
touch button backlight (10, 11) will go out.
– You can switch the operating kettle off by pressing the
power button (11), the kettle flask backlight will be
switched off, after which the display (6) and the back-
light of the touch buttons (10, 11) will go out.
– After switching the kettle off, wait for 10-20 seconds,
after which you can switch it on to boil water again.
Water heating mode
– This kettle also allows you to heat water to a tempera-
ture in the range from 40 to 90 °C with an increment
of 10 °C. To select the desired heating temperature,
press the button (11), you will hear a sound sig-
nal, and the backlight of the touch buttons (10, 11) will
be switched on. By pressing the button (10) select the
desired heating temperature which will be shown on the
display (6), then press the button
The heating process will start, the temperature of the
water will be shown on the display (6), and you will also
see the backlight of the buttons (10, 11) and the flask
of the kettle.
– When the water is heated to the set temperature, you will
hear three sound signals, the heating process will stop,
the backlight of the kettle flask will be switched off, after
which the backlight of the buttons (10, 11) and the dis-
play (6) will go out.
– You can switch the operating kettle off by pressing the
power button
switched off, after which the backlight of the touch but-
tons (10, 11) and display (6) will go out.
– After switching the kettle off wait for 10-20 seconds,
after which you can switch it on to heat the water once
more.
Note: You can choose temperature measurement unit:
°С or °F by pressing and holding the button (10) for more
than 3 seconds.
Keep Warm mode
To set the temperature for the Keep Warm mode, press
(11) again. the button
light of the touch buttons (10, 11) and the display (6) will
be switched on. Press and hold the button
(11). The boiling more than 3 seconds, the Keep Warm mode indicator (12)
will appear on the display (6) and the temperature indica-
tions will be flashing. By pressing the button (10) select
the desired heating temperature in the range from 40 to
90 °C with an increment of 10 °C, it will be shown on the
display (6). The kettle will maintain the set temperature for
2 hours provided that the kettle has not been removed from
the base (8). In this case, the display (6) will show the main-
tained water temperature, Keep Warm mode indicator (12),
and you will also see the backlight of the buttons (10, 11)
and the kettle flask.
Note: If the temperature of the Keep Warm mode is higher
than the temperature of the water in the kettle, the kettle
will heat the water to the set temperature, after which it will
switch to the Keep Warm mode.
To switch the Keep Warm mode off press the button
(11), the kettle flask backlight will be switched off, after
which the display (6) and the backlight of the touch buttons
(10, 11) will go out.
Note: If you accidentally switch the kettle on without water,
the automatic thermal fuse will trip and the kettle will be
switched off. In this case take the kettle from the base (8),
let it cool down for 10-15 minutes, then fill it with water and
switch it on, the kettle will operate in normal mode.
(11) once more.
Note: There is a cord storage (9) on the reverse side of the
base (8). Adjust the optimal power cord length by folding it
in a corresponding way.

CLEANING AND CARE

– Before cleaning disconnect the unit from the mains, pour
out water and let the kettle cool down.
11
(11), the kettle flask backlight will be
(11), you will hear a sound signal, the back-
(11) for