Cleaning And Care - Rondell Rde-1621 Die Betriebsanweisung

– To stop the program at any stage, press the «Keep
Warm/Cancel» button (22).
Note: if you want to heat up the second dish, then in the
capacity of the multicooker (it is recommended to add
a certain amount of liquid, which will protect the food
from burning.
«Multicook» mode
The Multicook program allows you to cook a variety
of dishes according to your individual recipe. In this
program, you can independently set the temperature
and time of heat treatment that you need. This mode
allows you to set up to 3 cooking stages.
1. To turn on this program, touch the «Multicook» but‑
ton (19).
2. The digital indicators (24) will flash intermittently with
the symbol « » and the recommended cooking time
for the first step of your recipe.
3. To change it, successively press the buttons (28)
«HOUR», «MIN» (
gram time.
4. Touch the «Temperature» button (20) to set the
desired cooking temperature.
5. Use the buttons (28) «HOUR», «MIN» (
set the required temperature value.
6. To move on to the next step in your recipe, touch the
«Multicook» button (19) again.
7. On the digital indicators (24), the symbol « » and the
cooking time of the second stage of your recipe will
flash intermittently.
8. Set the cooking time and temperature as described
in steps 3‑5.
9. To move on to the next step in your recipe, touch the
«Multicook» button (19) again.
10. On the digital indicators (24), the symbol « » and
the cooking time of the third stage of your recipe will
flash intermittently.
11. Set the cooking time and temperature as described
in steps 3‑5.
12. Wait 3 seconds for the cooking process to start. The
symbol of the cooking stage will blink intermittently

CLEANING AND CARE

•
•
•
Note: when removing the inner lid (16), never pull on its
O-ring. This may damage it.
•
•
•
•
) to set the desired pro‑
•
•
) to
•
•
•
•
22
on the display, and the digital indicators (24) will
begin the countdown of the time of this stage.
Unplug the unit and let it cool down.
Press the button (4) and lift the lid (3) to the verti‑
cal position.
Press the «PUSH» button (17) and remove the inner lid
(16) upwards (fig. 3)
Remove the steam valve (7). To do this, grasp the
ledge of the right upper part of the valve and pull it in
the direction from the base of the lid (3) (fig. 4).
Dismantle the steam valve (7). Open the steam valve
latch to separate the upper and lower parts (fig. 5).
Rinse the valve (7) with warm water with the addition
of a neutral detergent, dry it, assemble the valve (7)
and install it in the lid (3) until the latch clicks (fig. 6).
Wipe the body (1) and the lid (3) with a slightly damp
cloth, then wipe dry.
Wipe the lid (3) from the inside.
Rinse the removable lid (16) with the gasket O‑ring
in clean warm water. Then wipe it with a soft cloth.
For heavy soiling, add a small amount of dishwashing
detergent to the water (fig. 7).
Pay attention to the condition of the O‑ring of the sil‑
icone gasket, if the gasket is defective, stop using
the multicooker and contact the service center to
replace it.
Install the removable inner lid (16) into the protrusions
of the lower part of the base of the multicooker lid
body (3), and press the upper part of the removable
lid until the latch clicks (fig. 8).
Wash the bowl (9), the steam cooking basket (10),
the measuring cup (11), the soup ladle (12), the rice
scooper (13) and the deep‑fry basket (14) with warm
water and neutral detergent, then rinse under running
water and dry.
The bowl (9) and steam tray (10) can be washed in
the dishwasher.