Cleaning And Care - Rondell Rde-1404 Betriebsanweisung

Vorschau ausblenden

Inhalt

Seite von 29

/ 29
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

– Place the bowl (5) on the installation place (7) and

turn it clockwise as far as it will go (pic. 3).

– Install one of the attachments (1, 2 or 3) on the

shaft (6), slightly press the attachment upwards and

turn the attachment counterclockwise as far as it will

go (Fig. 4). Make sure that the attachment is fixed

properly.

– Put the necessary ingredients into the bowl (5).

– Press and hold down the button (9) (Fig. 5), pressing

on the upper part of the motor unit (8) (Fig. 6), set it

to the operating position and release the button (9).

Make sure the motor unit (8) is fixed properly in the

operating position (Fig. 7).

Note: there is an opening in the lid (4) for adding ingre-

dients during the kitchen machine operation.

– Insert the power plug into the mains socket.

– Switch the kitchen machine on by turning the oper-

ation mode switch (11), set the required attachment

rotation speed (see the chapter "ATTACHMENTS").

– Add necessary ingredients during the kneading pro-

cess to the loading hole in the bowl lid (4).

– During the operation of the motor unit (8), the light

ring (14) will light up.

– When switching the operation mode switch to the

position «0», the operation of the motor unit (8) will

be stopped, the light ring (14) will go out.

– Use the mode «P» to quickly mix ingredients at max-

imum speed. The mode is activated by turning and

holding the mode switch (11) from the position «0»

(on) to the position «P». The light ring (14) will glow

at the same time. If you release the mode switch (11),

it will return to the position «0», the operation of the

motor unit (8) will stop. The light ring (14) will go out.

Note:

– During operation of the device, do not allow metal

objects, knives, spoons, forks, etc., to get into the

bowl (5). This can cause damage to the attachments,

the bowl and the device itself, as well as cause injury.

– If the motor unit lock button (9) is pressed during

operation of the motor unit (8), the operation of the

motor unit (8) will be blocked. To continue working,

press the upper part of the motor unit until it is fully

fixed with the lock button (9) in the working position.

Turn the mode switch (11) to the position «0». After

that set it to the desired mode.

– Maximal continuous operation time of the kitchen

machine is no more than 5 minutes. Make at least a

10 minute break before switching the unit on again.

– Do not block the ventilation openings on the motor

unit (8) during the unit operation; this may lead to the

electric motor overheating.

– If the motor thermal protection trips and stops during

operation, disconnect the kitchen machine from the

electric mains. Switch the unit on again only after the

motor has completely cooled down, but not earlier

than after 40-45 minutes.

– After you finish the unit operation, set the operation

mode switch (11) to the position «0» and unplug the

unit from the electric socket.

– Holding the motor unit (8) with your hand, press and

hold the button (9), lift the motor unit (8) and fix it in

the upper position (Fig. 5).

– If necessary, you can use a plastic spatula (13) to gently

clean the stuck ingredients from the attachments (1-3)

and the bowl (5) until they are completely removed.

– Remove the installed attachment turning it clockwise.

– Remove the bowl lid (4).

– Remove the bowl (5) by turning it counterclockwise.

– Take the ingredients out of the bowl (5).

– Wash the attachment and the bowl (5) with warm

water and a neutral detergent, rinse them and dry.