Basic Operation - Denon DN-S1000 Bedienungsanleitung

BASIC OPERATION

5
Play and pause
• Each push of the y PLAY/PAUSE (13) button
switches between playback and pause. y
PLAY/PAUSE (13) button illuminates solid green
during playback and flashed in pause.
• When the y PLAY/PAUSE (13) button is pushed
during play, the DN-S1000 pauses playback at that
point. Push y PLAY/PAUSE (
13 ) button once
again and playback resumes.
• Playback will pause when SCRATCH is selected
with the !8 DISC MODE button and the scratch disc
is held with your hand. Playback resumes when
your hand is released.
Play and Cue
• When the i CUE button is pushed during playback,
the track stops and returns to the original position of
which playback started from, the (Cue point). This
function is also called Back-Cue. With the Back-Cue
function, you can start from exactly same position.
The i CUE button illuminates solid red when DN-
S1000 is ready to start playback.
• You can set and change Cue point as follows.
• When you started playback.
• Track select finished.
• manual search.
Select the track
• Turn the @3 TRACK knob.
• By pushing @3 TRACK knob down while turning, the
tracks will increment 10 at a time.
!
Move the Cue point
• If you would like to start playback other from the
beginning of the track, you need to move Cue Point
using fast Search and manual search function.
You can move to the approximate playback
start position by @4 or @5 FAST SEARCH
buttons.
QUICK JUMP
[QUICK JUMP]
• If the FAST SEARCH button
is tapped shortly, the
FAST SEARCH
1
playback position jumps about 10 seconds.
The jump time can be selected in the
preset mode from 10,20,30 or 60 sec.
[FAST SEARCH]
• When the FAST SEARCH button is pressed
and held in, the disc is fast-searched.
Push the !8 DISC MODE
DISC MODE
button to set o Scratch
2
ON : SCRATCH
Disc to search mode. The
OFF : SEARCH/
!8 DISC MODE button
BEND
LEDs will turn off.
Turn the o Scratch Disc to
change Cue point. You can hear
the short sound of the current
3 Cue point.
When o Scratch Disc is turned in the pause,
Cue or frame repeat mode, it works as the
manual search function.
After you found your
preferred Cue point, push
CUE
4 the i CUE button then a
new Cue point is set.
CUE/STUTTER
Adjusting the pitch
• With Pitch slider you can adjust the playback speed
(Pitch).
• If you would not prefer to change key of sound, use
the Key Adjust function.
Push the @9
PITCH/KEY
PITCH/KEY
button to PITCH LED lights up.
1
RANGE
• PITCH → KEY (key adjust) → OFF
Pitch decreases
Move the @8 Pitch slider to adjust
the pitch. The current pitch setting
2
0
is displayed on the display.
Pitch increases
DN-S1000 has five pitch ranges,
4%, 10%, 16%, 24% and 100%.
When the @9
RANGE button
is pushed for more than 1 sec,
3
the pitch range can be selected
PITCH/KEY
with the @3 PARAMETERS
knob.
RANGE
• When the @3 PARAMETERS PARAMETERS
PUSH
knob is pushed the pitch
range is entered and the
3
pitch range selection mode
is cancelled.
TRACK SEARCH
MP3 SEARCH MODE
Pitch Bend
• With PITCH BEND function you can change pitch
temporary. DN-S1000 has two ways for this
function PITCH BEND buttons and Scratch Disc.
[PITCH BEND +/– buttons]
• Push the @6 PITCH BEND
– or @7 + button for
PITCH BEND
momentary change of
1
pitch.
While holding these buttons down, the pitch
continues to change up to the limitation.
• After releasing the PITCH BEND buttons,
playback pitch returns to slider setting.
[Scratch Disc]
• When the disc mode is set to
SEARCH/BEND with the !8 DISC
MODE button, the playback speed
2
can be changed by turning o
Scratch Disc during playback.
Power on play
• When "POWER ON PLAY" is set to "ON" at "
PRESET (10)", playback starts from the first track
on the disc when the power is turned on.
⁄4
ENGLISH
11