Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Reset to factory settings
When resetting to factory settings, all personal data is
deleted!
While the earphones are
�
in the charger, press and
hold the button on the
charger for 12 seconds
until the LED on the
charger flashes yellow.
Peer Pairing
To pair new earphones (e.g. when replacing defective
or lost earphones), both sets of earphones must be
reset to factory settings so that they can connect.
During peer pairing the LED on the charger flashes
rapidly blue.
Overview of operating functions
Earphones in ear
Start / stop media
playback
Switch between noise
cancellation (ANC) and
transparency mode
Activate voice assistant
Accept incoming call
Reject incoming call /
end active call
Increase volume
Reduce volume
Play next track
Play previous track
Both earphones in the
charger
Switch to pairing mode
Delete pairing list
Reset to factory settings
AMIRON 100 — True Wireless Earphones
Operation (earphones)
�
Tap once ( )
�
Tap twice (
)
Tap twice and hold with
�
the second tap (
)
Tap once ( )
�
Tap twice (
)
�
�
Tap and hold right
(
)
Tap and hold left
�
(
)
Tap right three times
�
(
)
Tap left three times
�
(
)
Operation (charging case)
Press and hold the
�
button approx. 5 s (
)
�
Press and hold the
button approx. 8 s
(
)
Press and hold the
�
button approx. 12 s
(
)
Overview of the LED displays on the
charging case
Charging case
Low battery warning
Charging via USB 0 – 30 %
Charging via USB 31 – 70%
Charging via USB 71 – 99%
Charging via USB 100%
Lid opened / 0 – 30%
Lid opened / 31 – 70 %
Lid opened / 71 – 100 %
Lid closed when not
charging
Bluetooth peer pairing
Bluetooth pairing
recognisable
Bluetooth connection in
charger
Bluetooth connection
possible
Bluetooth connection lost
Delete pairing list
Restoring the factory
settings for the earphones
Cleaning
Due to dirty eartips and the formation of a warm and
humid climate in the ear canal, an increased germ level
can lead to a higher risk of ear canal infections.
Therefore, please clean the eartips regularly.
Remove the eartips from the housing.
�
Clean the eartips under running lukewarm water
�
and a little ph-neutral soap or with a soft, lint-free
moistened cloth.
�
Remove any cerumen that may be inside the eartip
with a cotton bud.
Then rinse off the soap and dry the eartips with a
�
lint-free cloth or leave them to dry overnight.
Only attach the eartips when they are completely dry
�
so that no remaining liquid can enter the electronics
of the earphone.
Clean the housing of the earphone with a soft, lint-
�
free cloth. If necessary, you can moisten the cloth
slightly with lukewarm water. Make sure that no liquid
can enter the housing.
Do not use any solvent-based cleaners, as these will
�
damage the surface.
If you want to remove cerumen from the housing,
�
make sure that you do not rub it into the small
openings for pressure equalisation and the micro-
phones.
8
LED display
�
LED flashes red rapidly
�
LED flashes red
LED flashes yellow
�
LED flashes green
�
LED illuminates green
�
�
LED flashes red slowly
LED flashes yellow
�
slowly
�
LED flashes green
slowly
LED is off
�
�
LED flashes blue rapidly
LED flashes blue and
�
red
�
LED is off
�
LED flashes blue slowly
LED flashes blue slowly
�
LED flashes blue
�
LED flashes yellow
�
Werbung
