Metabo RSEV 19-125 RT Originalbetriebsanleitung Seite 14

en ENGLISH
9. Cleaning, Maintenance
Cleaning the motor: It is possible that particles
deposit inside the power tool during operation. This
impairs the cooling of the power tool.
The power tool should be cleaned regularly, often
and thoroughly through all front and rear air vents
using a vacuum cleaner or by blowing in dry air.
Prior to this operation, separate the power tool from
the power source and wear protective glasses and
a suitable dust mask. Ensure appropriate suction is
available when blowing out vents.
Replacing the spring-mounted ring brush:
Replace worn brushes for optimal dust extraction.
Replacement brush set: Order No. 6.28214.
10. Troubleshooting
Machines with VTC and TC electronics:
The electronic signal display lights up
and the load speed decreases (not
W...RT). (15) There is too much load on the
machine! Run the machine in idling until the
electronics signal indicator switches off.
The machine does not start. The
electronic signal display (15) (depends
on model) flashes. The restart protection is
active. If the mains plug is inserted with the machine
switched on, or if the power supply is restored
following an interruption, the machine does not start
up. Switch the machine off and on again.
11. Accessories
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
Always use the suitable tool and the supplied
guard for the application.
Task: Surface grinding
- Tool: "Masonry/concrete" diamond cup wheel
Work only with appropriate dust extraction: connect
an all-purpose vacuum cleaner class M to the
extractor connection piece.
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
A defective mains cable must only be replaced with
a special, original mains cable from metabo, which
is available only from the Metabo service.
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
14
13. Environmental Protection
The sanding dust generated may contain
hazardous materials: do not dispose of this dust
with household waste, but at a special collection
point for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2012/
19/EU on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
14. Technical specifications
Explanation of details on page 3. Subject to change
in line with technical advances.
Ø = max. diameter of accessory
t = Max. permitted thickness of clamping
max,1
shank on accessory when using
clamping nut (6)
M = Spindle thread
l = Length of the grinding spindle
n* = No-load speed (maximum speed)
P = Nominal power input
1
P = Power output
2
m = Weight without mains cable
Measured values determined in conformity with
EN 62841.
Machine in protection class II
~
Alternating current
* Energy-rich, high-frequency interference can
cause fluctuations in speed. However, the fluctua-
tions disappear as soon as the interference fades
away.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
Using these values, you can estimate the
emissions from this power tool and compare these
with the values emitted by other power tools. The
actual values may be higher or lower, depending on
the particular application and the condition of the
accessory or power tool. In estimating the values,
you should also include work breaks and periods of
low use. Based on the estimated emission values,
specify protective measures for the user - for
example, any organisational steps that must be put
in place.
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841:
a = Vibration emission level
h, S
(grinding)
K = Uncertainty (vibration)
h,...