En Original Instructions; Declaration Of Conformity; Specified Use; General Safety Instructions - Metabo Rsev 19-125 Rt Originalbetriebsanleitung

en ENGLISH
Original instructions

1. Declaration of Conformity

We declare under our sole responsibility: These
concrete grinders, identified by type and serial
number *1), comply with all relevant requirements of
the directives *2) and standards *3). Technical file
at *4) - see page 3.
For UK only:
We as manufacturer and authorized person to
compile the technical file, see *4) on page 3,
hereby declare under sole responsibility that these
renovation routers, identified by type and serial
number *1) on page 3, fulfill all relevant provisions of
following UK Regulations S.I. 2016/1091, S.I. 2008/
1597, S.I. 2012/3032 and Designated Standards
see *3) on page 3.

2. Specified Use

When fitted with original Metabo accessories, the
concrete grinder is suitable for grinding and
removing concrete, screed and coatings with
diamond cup wheels.
Do not use for abrasive cutting-off operations,
roughing work, sanding, polishing or flap disc work.
The machine must not be used with water.
Note: The ring brush may stick when thermoelastic
materials are processed.
The machine is suitable for commercial use in trade
and industry.
Always use a suitable dust extraction system:
Connect a vacuum cleaner (M-class) to the
extractor connection piece (12).
The user bears sole responsibility for any damage
caused by improper use.
Generally accepted accident prevention regula-
tions and the enclosed safety information must be
observed.

3. General safety instructions

For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Read the operating
instructions to reduce the risk of injury.
WARNING – Read all safety warnings,
instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
Always include these documents when passing on
your power tool.
10

4. Special Safety Instructions

4.1 General safety instructions for grinding:
a) This power tool is designed for surface
grinding. Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow all
instructions listed below may result in electric
shock, fire and/or serious injury.
b) Operations such as routing, sanding, wire
brushing, polishing, hole cutting or cutting-off
are not recommended to be performed with
this power tool. Operations for which the power
tool was not designed may create a hazard and
cause personal injury.
c) Do not convert this power tool to operate in a
way which is not specifically designed and
specified by the tool manufacturer. Such a
conversion may result in a loss of control and cause
serious personal injury.
d) Do not use accessories which are not
specifically designed and specified by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
e) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
f) The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or
controlled.
g)The dimensions of the accessory mounting
must fit the dimensions of the mounting
hardware of the power tool. Accessories that do
not match the mounting hardware of the power tool
will run out of balance, vibrate excessively and may
cause loss of control.
h) Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks, backing
pad for cracks, tear or excess wear, wire brush
for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After
inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run the
power tool at maximum no-load speed for one
minute. Damaged accessories will normally break
apart during this test time.
i) Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As
appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by