Metabo RSEV 19-125 RT Originalbetriebsanleitung Seite 13

- Fit locking discs (3) to the left and right of the gear
housing.
- Fit the bar auxiliary handle (1) at the gear housing.
- Insert the thumb screws (2) left and right into the
bar auxiliary handle (1) and turn gently.
- Adjust the bar auxiliary handle (1) to the required
angle.
- Firmly tighten the thumb screws (2) to the left and
right manually.
6.2 Dust extraction
Always use a suitable dust extraction system:
Connect an M-class vacuum cleaner to the
extractor connection piece (12).
For optimal dust extraction, use the connecting
sleeve 6.30796.
We recommend using an antistatic suction hose
with diameter 35 mm.
7. Attaching the accessory
Disconnect the mains plug before changing
any accessories. The machine must be
switched off and the spindle must be at a standstill.
7.1 Locking the spindle
Press in the spindle locking knob (11) only
when the spindle is stationary!
- Press in the spindle locking button (11) and turn
the
spindle (9) by hand until you feel the spindle
locking button engage.
7.2 Fitting/removing the diamond cup wheel
See illustration B on page 2.
To fit:
- Fit the support flange (8) on the spindle. (9) The
flange should not turn on the spindle when prop-
erly attached.
- Lay the diamond cup wheel (7) on the support
flange (8) so that it lies flat along the support
flange.
- The two sides of the clamping nut (6) are different.
Screw the clamping nut onto the spindle so that
the band of the clamping nut (6) is facing upward.
- Lock the spindle (see chapter 7.1). Turn the
clamping nut (6) clockwise using the 2-hole
spanner (5) to secure.
To remove:
- Lock the spindle (see chapter 7.1). Turn the
clamping nut (6) anticlockwise using the 2-hole
spanner (5) to unscrew.
8. Use
8.1 Working close to walls
To open and close the segment: switch off the
machine and pull the mains plug. The acces-
sory must be stationary.
Only raise the segment (13) when working
close to walls. Otherwise, the segment must
be lowered.
The open area of the safety guard must face the
direction of the wall.
8.2 Setting the speed
Set the optimum speed on the setting wheel (16),
depending on the application.
A wheel setting of between 4 and 6 is suitable for
most applications.
8.3 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only set it
down when the motor has come to a standstill.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate on the work.
Machines with the designation W...RT:
Torque activation (with dead man's lever)
I
Switching on: Slide the trigger switch (17)
forwards and then push the trigger switch
(17) upwards.
Switching off: Release the trigger switch (17).
Machines with the designation W...RT:
Continuous operation (depending on features)
I
Switching on: Switch the machine on as described
above. Now slide the trigger switch (17)
forwards again and release in the front
position to lock the trigger switch (17)
(continuous operation).
Switching off: Push the trigger switch (17)
upwards and release.
8.4 Working Directions
Surface grinding:
Place the machine with the entire surface of the tool
onto the workpiece. Apply moderate pressure and
move it to and fro across the surface.
ENGLISH en
16
0
16
0
13