Silverline 947560 Bedienungsanleitung Seite 6

EN
Before Use
Fitting Accessories
WARNING:Ensure the heat gun is disconnected from the power supply and fully cooled before
attaching or changing any accessories, or making any adjustments.
• The Accessory Nozzle (5) supplied allows the heat gun to be used for a variety of different tasks
• Accessories are a push-fit onto the Outlet Nozzle (1)
Operation
• Always hold the machine by the handle provided
• Do not obscure the Inlet Vents (2)
• Always wear appropriate personal protective equipment for the job at hand. Use of this machine
requires ear defenders, safety goggles, gloves and a breathing mask
Switching ON and OFF
• The outlet has two pre-set temperatures. This can be adjusted by changing the position of the
ON/OFF Switch (3)
• For the lower setting (300°C) move the Switch into the 'I' position
• For the higher setting (500°C) move the Switch into the 'II' position
• To switch the heat gun OFF move the ON/OFF Switch to the '0' position
• Be aware that the metal parts of the tool will remain hot for some time after switching OFF. Allow
at least 30mins for the gun to cool before leaving unattended
Paint stripping
• Connect the tool to the mains supply and switch ON
• Direct the hot air onto the paint to be removed, keeping the Outlet Nozzle (1) at least 25mm
away from the surface
NOTE: Take extra care when removing paint from window frames. The heat from this tool can cause
damage to glass if used carelessly .
• Allow the paint to soften and remove using a suitable scraper
• Do not overheat the paint. If you notice smoke or blackening, stop heating
• Do not allow waste to build up or drop into the Outlet Nozzle as this will cause a fire hazard
Pipe defrosting
• This heat gun can be used to defrost frozen water pipes
• Using a suitable attachment, aim hot air at the frozen pipe. Move the heat gun along the pipe so
that the whole length defrosts evenly
• Be aware of overheating areas directly behind the pipe being defrosted
• Do not attempt to defrost PVC pipe as the heat of the air may cause permanent damage
Drying
• This heat gun can be used to dry out damp wood or other materials
• Be very careful when operating power tools near damp materials, the presence of water greatly
increases the danger of electric shock
• Always refer to the product manufacturer's instructions if using the heat gun to dry plaster, paint,
or other finishes. Do not use the hot air gun/heat gun on any flammable material, or any material
that may produce hazardous fumes
Stationary use
• This hot air gun can also be used statically, keeping hands free to manipulate the workpiece
• The heat gun is designed to stand upright on a suitable workbench. The Outlet Nozzle (1) should
point straight upwards. The nozzle must not contact the workbench or any other object
• Ensure that the Power Cord (4) is well supported, and will not become caught as you work
• Switch the heat gun ON, and move the workpiece into the hot air flow. Take care to keep your
hands and face away from the hot air
6
Accessories
A range of accessories is available from your Silverline stockist to enhance the functionality of your
heat gun. Spare parts are available from your Silverline stockist or www.toolsparesonline.com.
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out any inspection,
maintenance or cleaning .
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should be
carried out by an authorised Silverline service centre. This advice also applies to extension cords
used with this tool
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the machine's service life
• Clean the body of your machine with a soft brush, or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes
Storage
• Store this tool in a secure, dry location out of the reach of children
• Allow the tool to cool down before storage
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: silverlinetools.com/en-GB/Support
UK Address:
Toolstream Ltd .
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
EU Address:
Toolstream B . V .
Hogeweg 39
5301 LJ Zaltbommel
The Netherlands
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools