Quick Reference Guide; Preparing The Devices For Use; Modell 21499 Walimex Pro Led Ringlight 380 Bi Color Rll-380Bv; Modell 21500 Walimex Pro Led Ringleuchte 500 Bi Color Rll-500Bv - Walimex Pro 380 Bi Color Gebrauchsanleitung

Operating Instruction

5. Quick reference guide

1. Please install the L shape camera
6. Preparing the device for use / mounting on a stand
bracket with bracket adjustment
7. Power supply
8. Operating the device
knob on the light.
10. Troubleshooting
NOTE
2. Install the light on light stand.
Detailed instructions for the following activities can be found in the relevant sec-
tions of these instructions for use. Strictly follow the sequence of the following
activities during fi rst time use, to prevent damage to the device.
WARNING
3. Install the camera onto the camera
With any action you take you should pay attention to the safety notes in the
bracket and tighten with the bracket and tighten with the
corresponding paragraphs.
camera fixing knob.

6. Preparing the devices for use

6.1. Model 21499 Walimex pro LED Ringlight 380 Bi Color RLL-380BV
1. Install the L shape light holder bra- 4. Make sure the power switch is OFF
cket (3) with bracket adjustment knob
before connecting the power cable
(6) on the light.
2. Install the light with the stand holder
or batteries.
(14) on a 1/4 or 3/8 inch thread on a
suitable lamp stand.
3. Install the camera onto the camera
bracket (3) and tighten with the
camera fi xing screw (2).
Instead of a camera, you can attach
your smartphone with the help of the ball
head and the smartphone holder. First secure the ball of
the ball head (16). Unscrew the fl ash shoe (17) from the
ball head. Attach the ball head to the camera mount (3). Screw the smartpho-
ne holder (15) onto the ball head. Check that it is securely in place. To tilt the
smartphone holder, loosen the rear screw, rotate it to the desired position and
tighten the screw again. Check that all parts are securely seated. Now carefully
32
page 32
page 34
page 35
page 37
1. Please install the L shape camera
bracket with bracket adjustment
knob on the light at the same
height.
Operating Instruction
2. Put the remaining part of the
camera bracket into L shape
insert your smartphone into the holder (17). The smart-
phone is held in place by spring tension. Do not release
bracket and tighten the bracket
1. Please install the L shape camera
the smartphone until it sits securely. Check again that it is
fixing knob.
bracket with bracket adjustment
securely seated, as the smartphone could slip downwards,
especially when shooting in portrait format.
knob on the light at the same
4. Check the secure fi xation of all screws.
3. Install the light on light stand. height.
5. The ringlight is ready for use.
6.2. Model 21500 Walimex pro LED Ringlight 500
2. Put the remaining part of the
4. Install the camera onto the camera
Bi Color RLL-500BV
camera bracket into L shape
bracket and tighten with the
1. Install the L shape light holder bracket (3) with bracket
bracket and tighten the bracket
camera fixing knob.
adjustment knob (6) on the light at the same height.
fixing knob.
2. Put the remaining part of the horizontal camera rail (15)
into L shape bracket (3) and tighten the bracket fi xing
5. Make sure the power switch is OFF
screws and adapter (16).
3. Install the light on light stand.
before connecting the power cable
3. Install the camera onto the horizontal camera mounting
rail (15) and tighten with the camera fi xing screw (2).
or batteries.
4. Install the camera onto the camera
Instead of a camera, you can attach your smartphone
with the help of the ball head and the smartphone
bracket and tighten with the
holder. First secure the ball of the ball head (16). Unscrew
camera fixing knob.
the fl ash shoe (17) from the ball head. Attach the ball
head to the horizontal camera mounting rail (15). Screw the smartphone holder
(15) onto the ball head. Check that it is securely in place. To tilt the smartphone 5. Make sure the power switch is OFF
holder, loosen the rear screw, rotate it to the desired position and tighten the
before connecting the power cable
screw again. Check that all parts are securely seated. Now carefully insert your
or batteries.
smartphone into the holder (17). The smartphone is held in place by spring
tension. Do not release the smartphone until it sits securely. Check again that
it is securely seated, as the smartphone could slip downwards, especially when
shooting in portrait format.
4. Check the secure fi xation of all screws.
5. The ringlight is ready for use.
NOTE
Please follow the user information issued by the tripod manufacturer.
33