RGB LED Band Inhalt Informationen zu dieser Bedienungsanleitung ..........4 Bestimmungsgemäße Verwendung ............... 4 Haftung ........................... 4 Service ........................... 5 Importeur .......................... 5 Technische Daten......................5 Sicherheitshinweise ....................6-8 Kinder .......................... 6 Spannungsversorgung ..................6 Kabel und Netzstecker ..................7 Unsachgemäße Handhabung ................
Seite 3
Contents Information about this operating manual ............18 Proper use ........................18 Liability ......................... 18 Service ......................... 19 Importeur ........................19 Technical data ........................ 19 For your safety ......................20-22 Children ........................20 Power supply ......................20 Cable and plug ...................... 21 Improper handling ....................22 Unpacking and checking ...................22 Installation ........................22...
RGB LED Band Vielen Dank, dass Sie sich für das RGB LED Band entschieden haben. Wir wünschen Ihnen viel Freude damit. Informationen zu dieser Bedienungsanleitung Diese Bedienungsanleitung enthält wichtige Informationen für einen ordnungsgemäßen und sicheren Betrieb des RGB LED Bands. Lesen Sie die Bedienungsanleitung daher vollstän- dig durch, bevor Sie das RGB LED Band einsetzen.
RGB LED Band Technische Daten Adapter Eingangsspannung: 100 – 240 V AC Ausgangsspannung: 12 V DC Frequenz: 50/60 Hz Eingangsstromstärke: 1,6 A Ausgangsstromstärke: 5 A Sicherheitshinweise Kinder WARNUNG! Verletzungsgefahr für Kinder! Wenn Kinder oder Personen, die die Gefahren nicht einschätzen können, mit dem RGB LED Band hantieren, besteht Verletzungsgefahr bis hin zum Tod.
BEDIENUNGSANLEITUNG • Sollten das RGB LED Band oder seine Anschlussleitung Beschä- digungen aufweisen, so berühren Sie es nicht. Schalten Sie zuerst die zugehörige Netzsteckdose stromlos (z. B. über den zugehörigen Sicherungsautomaten) und ziehen Sie danach den Netzstecker vorsichtig aus der Netzsteckdose. Betreiben Sie das Produkt danach nicht mehr, sondern wenden Sie sich an den Hersteller oder bringen Sie es in eine Fachwerkstatt.
RGB LED Band Unsachgemäße Handhabung Verletzungsgefahr durch unsachgemäße Handhabung! Die unsachgemäße Handhabung des RGB LED Bands kann zu Verletzungen führen. • Achten Sie auf eine sachgerechte Inbetriebnahme des Gerätes. Beachten Sie hierbei diese Bedienungsanleitung. • Wenden Sie sich an den Hersteller oder eine Fachkraft, wenn Sie Zweifel über die Arbeitsweise, die Sicherheit oder den Anschluss des RGB LED Bands haben.
Seite 9
BEDIENUNGSANLEITUNG Um einen optimalen Halt des RGB LED Bands zu gewährleis- ten, müssen die Anbringflächen trocken, ausreichend eben, sauber und fettfrei sein. 3. Ziehen Sie die Klebefolie von der Rückseite des RGB LED Bands ab. 4. Kleben Sie das RGB LED Band sofort an. Abb.
Seite 10
RGB LED Band Abb. 2 6. Stecken Sie den Stecker (Abb. 2/4) des Netzteils in die Anschlussbuchse des Controllers (Abb. 2/5). 7. Stecken Sie den Netzstecker des Netzteils in die Steckdose. 8. Das RGB LED Band kann auf Wunsch auf Ihre ideale Länge gekürzt werden.
BEDIENUNGSANLEITUNG Übersicht Fernbedienung Abb. 3 Funktionen abrufen Funktionen Abrufen Drücken Sie diese Taste, um die Helligkeit zu Helligkeit erhöhen erhöhen. Drücken Sie diese Taste, um die Helligkeit zu Helligkeit verringern veringern. Drücken Sie diese Taste, um das RGB LED Band Einschalten einzuschalten.
Seite 12
RGB LED Band Drücken Sie diese Taste, um die Flash-Funktion Flash-Funktion einzuschalten. Rot, Grün und Blau leuchten ab- einschalten wechselnd und zusammen. Drücken Sie diese Taste, um die Strobe-Funktion Strobe-Funktion einzuschalten. Rot, Grün und Blau blinken gleich- einschalten zeitig. Drücken Sie diese Taste, um die Fade-Funktion Fade-Funktion einzuschalten.
BEDIENUNGSANLEITUNG Störungstabelle Fehler- Ursache Abrufen beschreibung RGB LED Band nicht mit Strom- Prüfen Sie, ob der Netzstecker netz verbunden in der Steckdose eingesteckt ist. Prüfen Sie, ob das RGB LED RGB LED Band nicht einge- Band über die Fernbedienung schaltet RGB LED Band eingeschaltet ist.
Seite 14
RGB LED Band • Lassen Sie Batterien nicht offen herumliegen. Es besteht die Gefahr, dass diese von Kindern oder Haustieren verschluckt werden. Suchen Sie in diesem Fall sofort einen Arzt auf. • Batterien dürfen nicht übermäßigen Temperaturen ausgesetzt werden, wie sie zum Beispiel im Sonnenschein, Feuer oder Backofen auftreten.
BEDIENUNGSANLEITUNG • LED-Bänder nur in abgerolltem Zustand betreiben LED- Bänder sind -wie alle Leuchtmittel- Verbrauchsartikel. Prüfen Sie bitte unbedingt VOR der Installation die LED-Bänder auf korrekte Funktion. Bereits verarbeitete Bänder sind von Reklamation, Umtausch oder Rücknahme ausgeschlossen! Reinigung WARNUNG! Lebensgefahr durch elektrischen Strom! Eine Reinigung des RGB LED Bands und seiner Komponenten bei vorhandener Spannungsversorgung kann zu gefährlichen Situationen führen.
RGB LED Band Entsorgung Elektrische und elektronische Bauteile dürfen nicht im Hausmüll entsorgt werden! Elektrische und elektronische Bauteile sowie die im RGB LED Band enthaltenen Batterien dürfen nicht im Hausmüll entsorgt werden. Batterien enthalten Schadstoffe, die nicht in die Umwelt gelangen dürfen. Wenn das Gebrauchsende erreicht ist, entsorgen Sie das RGB LED Band sowie die Batterie entsprechend lokal geltenden Entsorgungsbestimmungen getrennt voneinander.
RGB LED Strip We are delighted that you have decided to purchase the RGB LED Strip. We hope it gives you great pleasure. Information about this operating manual This operating manual contains important information for the proper and safe operation of the RGB LED Strip. That is why we suggest that you read the entire operating manual before using the RGB LED Strip.
USER MANUAL Service Service First Flash GmbH Address Lived – X4-LIFE Donaustraße 20 D-38120 Braunschweig Telefon +49 (0) 531/224356-82 E-Mail service@x4-life.de Internet www.x4-life.de Importeur Address lived non food GmbH Theodor-Heuss-Straße 3 D-38122 Braunschweig E-Mail info@lived-non-food.de Internet www.lived-non-food.de Technical data Technical data for RGB LED Strip...
RGB LED Strip Technical data for adapter Input voltage: 100 – 240 V AC Output voltage: 12 V DC Frequency: 50 – 60 Hz Input current: 1.6 A Output current: 5 A For your safety Children WARNING! Children are at risk of injury! If the RGB LED Strip is handled by children or adults unable to assess the risks, they run the risk of injury, which could even be lifethreatening.
USER MANUAL • Do not touch the RGB LED Strip or the connecting cable if there are signs of damage. First isolate the socket (e.g. by switching it off at the fuse box) and then carefully take the plug out of the socket. Do not continue to use the product once this has occurred and instead contact the manufacturer or take it to a service centre for repair.
RGB LED Strip Improper handling WARNING! There is a risk of injury as a result of improper handling! Improper handling of the RGB LED Strip can lead to injuries. • Make sure that the unit is switched on and used correctly. Please note the operating instructions in this respect.
Seite 23
USER MANUAL 3. Peel off the adhesive film from the back of the RGB LED Strip. 4. Immediately fix the RGB LED Strip in position. Fig. 1 5. Push the connector plug (Fig. 1/1) of the RGB LED Strip into the connector socket (Fig.
Seite 24
RGB LED Strip Fig. 2 6. Push the plug (Fig. 2/4) of the mains adapter into the socket on the control unit (Fig. 2/5). 7. Push the plug on the mains adapter into the mains socket. 8. The RGB LED Strip can be shortened to the optimal length. For this purpose cut the tape with scissors at the copper- colored connection.
USER MANUAL Remote control overview Fig. 3 Using the functions Functions Call up Increase brightness Press this button to increase the brightness. Decrease brightness Press this button to decrease the brightness. Power on Press this button to turn the LED RGB Strip on. Taste OFF Press this button to turn the LED RGB Strip off.
RGB LED Strip All colors Press this button to cycle through all colors. Press this button to enable the flash function. Enable flash Red, green and blue will light up alternately and function together. Enable strobe Press this button to enable the strobe function. function Red, green and blue will blink simultaneously.
USER MANUAL The remote control is not Check that the remote control switched on is switched on. Battery in remote control is Replace the battery in the dead remote control. Check that the battery has Remote control Battery is not inserted correctly been inserted the right way does not work round.
RGB LED Strip ➝ Make sure the polarity is correct. This is shown on the back of the remote control. ➝ Slide the battery housing into the battery compartment of the remote control until it clicks into place. ➝ Dispose of the old battery properly to reduce the impact on the environment ->...
USER MANUAL Disposal Electrical- and electronic devices must never be disposed of in a regular household waste! Electrical and electronic components as well as the batteries used in the RGB LED Strip must not be disposed of as regular household waste. Batteries contain hazardous materials that must not be allowed to enter the environment.