Inhalt Informationen zu dieser Bedienungsanleitung ..........4 Auspacken und Prüfen ....................4 Packungsinhalt ......................4 Bestimmungsgemäße Verwendung ..............4 Allgemeine Hinweise ....................5 Importeur und Service ....................6 Sicherheitshinweise ....................6 Anschluss und Inbetriebnahme ................8 Reinigung und Pflege..................... 10 10. Entsorgung......................... 10 11. Technische Daten ....................11 Information on this user manual ................
Stroboskop Es freut uns, dass Sie sich für dieses Produkt entschieden haben. Wir wünschen Ihnen viel Freude damit. 1. Informationen zu dieser Bedienungsanleitung Diese Bedienungsanleitung enthält wichtige Informationen für einen ordnungsgemäßen und sicheren Betrieb des Pro dukts. Lesen Sie die Bedienungsanleitung vollständig durch, bevor Sie das Produkt einsetzen.
6. Importeur und Service Service lived non food GmbH Adresse TOR 8 – 9 Donaustraße 20 D38120 Braunschweig Telefon +49 (0) 531/22435682 E-Mail service@x4life.de Internet www.x4life.de Adresse lived non food GmbH Donaustraße 20 D38120 Braunschweig E-Mail info@livednonfood.de Internet www.livednonfood.de 7. Sicherheitshinweise • Die folgenden Sicherheits...
Seite 7
• Eine Reparatur oder ein Öffnen des Gerätes darf nur durch eine Fachkraft erfolgen, die mit den damit verbundenen Ge fahren bzw. einschlägigen Vorschriften vertraut ist. Es dürfen nur Originalersatzteile verwendet werden. • Das Produkt darf nicht feucht oder nass werden. Stellen Sie keine Gefäße mit Flüssigkeiten, z.B.
• Das Produkt sollte nicht extremer Hitze oder Kälte ausgesetzt werden. Lassen Sie das Produkt nicht in der prallen Sonne liegen oder in der Nähe von offenem Feuer oder extremen Wärmequellen: Lagertemperatur: 0°C bis 60°C; Betriebstem peratur: 0°C bis 40°C • Dieses Produkt darf nur in Innenräumen verwendet werden.
Sie können den Montagebügel auch abschrauben um diesen leichter an einer Wand oder der Decke zu verschrauben. Schrauben Sie den Montagebügel dann wieder an das Gehäu se. Bohren oder schrauben Sie zur Befestigung des Produkts keine zusätzlichen Schrauben in das Gehäuse. Wenn Sie das Gerät nur auf eine gerade Fläche stellen möch...
Mit dem Drehschalter regeln Sie die Blitzgeschwindigkeit des Stroboskops. Nach 5 Stunden Betrieb, das Gerät 15 min. abkühlen lassen und erst dann wieder in Betrieb nehmen. 9. Reinigung und Pflege HINWEIS: Sachschaden durch unsachgemäße Reinigung! Ätzende oder scheuernde Reinigungsmittel können das Produkt und seine Komponenten beschädigen.
11. Technische Daten • Blitzröhre 5 W Länge: 63 mm Ø: 3,6 mm • Geschwindigkeitsregler • Betriebsspannung 220 – 240 V AC /50 Hz • Abm.: 125 x 82 x 52 mm Montageloch Blitzröhre Montagebügel Gehäuse Scheibe Netzkabel Geschwindigkeitsregler...
Seite 12
Strobe Light Hanging Hole Flash tube Handle Main Unit Transparent Film Power cable Speed Knob...
We are pleased that you have decided to buy our product. We wish you were a lot of fun with this product. 1. Information on this user manual This user manual contains important information for the safe use of the product. Therefore, for your own safety and for a successful use, please read this user manual completely before assembling and using the product.
Address lived non food GmbH Donaustraße 20 D38120 Braunschweig E-Mail info@livednonfood.de Internet www.livednonfood.de 7. Safety guide • Please read the safety guide before using the product. This information is for your safety and the protection of the device and devices connected. You will also find specific safety instructions in the following chapters of this user manual.
Seite 16
• Make sure that the connector cables to not become a hazard. The mains cable should not be lent, squashed or damaged by sharp edges. • Should the mains cable show any signs of damage, do not use the device. Detach it from the mains plug immediately and let it be repaired by a qualified person.
• If you have doubts on the function or questions, please contact your local dealer or our service center. 8. Getting started The MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable Mounting The LED strobe light can be mounted to the ceiling or on walls.
Operation Plug the power plug into a safe mounted and approved 230 V wall socket. The product is now ready for use and has no additional on / off switch. With the rotary switch you can control the flash rate of the strobe light. After 5 hours of use, let the device cool down for at least 15 min.