Behringer B1C Schnellstartanleitung Seite 9

16
B1C
B1C Getting started
(EN) Step 3: Getting
Connect the B1C to a power outlet by
using the included IEC power cable.
started
This will also charge up the
internal battery.
Connect all analog microphone and/or
instrument cables to their respective
input jacks. Make sure all outboard audio
gear is switched off for now.
Power up the B1C by pressing the
AC/POWER switch to the "on" position.
If the AC power is not connected, the B1C
will run on internal battery power.
Reduce the volume by rotating all the
VOLUME knobs counter-clockwise.
Power up any outboard audio gear
connected to the B1C.
Raise the volume back up to a low-to-
medium setting.
Speak or sing into each microphone and
play your instrument while raising the
respective volume level (A or B) until you
find a comfortable gain level that does
not distort the audio signal. Please avoid
clipping the input signal.
If you intend to stream Bluetooth audio,
go to the Bluetooth Streaming section of
this Quick Start Guide and follow the
setup instructions.
Set Bluetooth levels by adjusting the
VOLUME until you find a comfortable
level. Do not forget to turn on the volume
on the sending BT device.
Bluetooth Connection
Adjust the Bass, Treble, and Reverb To stream audio from a Bluetooth-enabled device, you will need at least one
settings as needed. B1C speaker and an iPad*/iPhone/Android*/Windows* device with basic
Bluetooth connectivity.
Note: When the AUX input is connected, it takes priority over Bluetooth.
Make final volume adjustments. Disconnect any AUX input of you want to use Bluetooth.
*iPad and Apple are trademarks of Apple Inc. Android is a trademark of Google
Inc. Windows is either a registered trademark or trademark of Microsoft
Corporation in the United States and/or other countries.
Bluetooth Streaming
To stream Bluetooth audio with any Bluetooth device (iPad/iPhone/Android/
Windows, etc.):
Single Speaker Operation
1. Enable Bluetooth on your remote device/smart phone.
2. Switch on your B1C speaker and minimize the volume.
3. Press the PAIR button on the B1C speaker.
4. Check that your remote device is searching for a connection.
5. Once your device detects the B1C speaker, select it from your remote device's
menu (for example "B1C").
6. Bluetooth music can now be streamed to your B1C. The stereo signal will
automatically mix down to mono.
7. The B1C speaker LED flashes on an off during pairing. It is solid when
connected and playing. It turns off if it fails to pair.
8. To unpair, press the PAIR button again.
Two Speaker Operation (TWS True Wireless Stereo)
Note: in TWS mode, only the Bluetooth signal is transmitted to the
second speaker.
1. Turn on both B1C speakers.
2. Press the PAIR button for more than 2 seconds on the first speaker (A).
3. Press the PAIR button for more than 2 seconds on the second speaker (B).
4. Speaker A's Bluetooth LED will flash quickly when ready for pairing,
5. Find the correct B1C name on the remote device and connect.
LED BUTTON VOLUME
6. Both speaker's Bluetooth LEDs will light solid after connecting successfully to
7. When streaming music to the speakers, the speaker B's (right channel)
8. To unpair from TWS, press the PAIR button for more than 2 seconds
Multiple Speaker (Mono) Operation
The Line output from each B1C speaker is a mix of all its inputs. It can be
connected to an input of the next B1C speaker in line. All speakers will
play in mono.
Quick Start Guide
This will become the left channel for stereo music.
This will become the right channel for stereo music.
and speaker B's LED will be solid when TWS pairing is successful.
the remote device.
LED will be solid, and speaker A's (left channel) LED will flash slowly
on speaker A or speaker B, and the two speakers will unpair TWS from
each other.
17