Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
HUMIDIFYING FUNCTION
Note:
- If the unit was subjected to negative tem-
peratures, then before first switching on it is
recommended to keep the unit for 30 min-
utes at room temperature.
- Use the unit when the room temperature
is from +5 to +40°С and relative humidity is
lower than 80%.
- Water temperature should not be above
+40°С.
1.
Unplug the unit.
2.
Take the handle (10), remove the tray (11)
and the water tank (9).
3.
Turn over the water tank (9), open the lid,
turning it anti clockwise.
4.
Fill the water tank (9) with the neces-
sary quantity of water and close the lid,
by matching the ledges on the lid with the
grooves on the water tank and then rotate
the lid clockwise.
5.
Place the filled water tank (9) on the tray
(11), and then install the assembled con-
struction into the unit. Wait for some time,
which is necessary for filling the operation
chamber with water.
6.
Connect the unit to the mains,
ton (7) to the "I" position, the power indi-
cator (28) will light up and you will hear a
sound signal.
7.
Switch on the unit, by pressing the on/off
button
(19), you will hear a sound signal,
unit operation in the fan mode indicator
(29) will light up and the room temperature
(21) indicator will be displayed.
8.
Press the (20) button to switch on the hu-
midifying function.
9.
You can control steam output intensity by
turning the handle (14).
10.
If during the humidifying function operation
the water tank (9) becomes empty, the (27)
indicator will light up on the display, and the
unit will give a signal to the user. In 3 min-
utes the unit will switch off automatically.
Note:
- If the water tank (9) becomes empty, the
(27) indicator will light up;
2130 Instr.indd 6
2130 Instr.indd 6
You should take off the water tank and fill it
with water.
- If during the humidifying function operation
the tray with the water tank is removed, the
unit will switch off automatically.
CLEANING AND CARE
Warning! Always switch off and unplug the
unit before cleaning.
Hard water causes appearance of mineral de-
posits on the sprayer, inner parts of the body
and in the water tank that leads to depression of
operation of the unit and appearance of white
bloom on the inner parts of the container and
the tray. To avoid it, it is necessary to clean the
sprayer weekly and to change water as often as
possible.
If you are not going to use the humidifying func-
tion for a long time:
- pour out water from the water tank and the
sprayer, wash the water tank, wash and
clean the operating chamber of the sprayer
and the sprayer itself, dry thoroughly and
take the unit away for storage.
Daily care
•
set the but-
Thoroughly wash the water tank (9) and the
tray under the water tank (11) once a week
with a solvent with a neutral detergent. After
it rinse them thoroughly with water.
•
Add 5-10 drops of purifying detergent on
the sprayer; wait about 2-5 minutes. Then
remove the bloom from the surface of the
sprayer.
Using the remote control
Open the lid of the battery compartment of the
remote control and insert 2 batteries of "ААА"
type, strictly following the polarity, close the
battery compartment lid.
•
Press the on/off button (36),
a sound signal, operation of the unit in the
fan mode indicator (29) will light up and
the room temperature indicator (21) will be
displayed.
•
Power is selected with the (35) button.
low power for small rooms heating, and
max. power for large rooms heating.
6
you will hear
Use
18.07.2011 10:21:10
18.07.2011 10:21:10
Werbung
