Werbung
Verfügbare Sprachen
Verfügbare Sprachen
• Check the equipment for damage which may have
occurred in transit. Report any damage immedi-
ately to the transport company which was used to
deliver the compressor.
• Install the compressor near the point of consump-
tion.
• Avoid long air lines and supply lines (extension
cables).
• Make sure that the intake air is dry and dustfree.
• Do not install the compressor in a damp or wet
room.
• The compressor may only be used in suitable
rooms (with good ventilation and an ambient tem-
perature from +5 °C to 40 °C). There must be no
dust, acids, vapors, explosive gases or inflamma-
ble gases in the room.
• The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor in
areas where work is conducted with sprayed water.
• The compressor may only be used outdoor briefly
when the ambient conditions are dry.
• The compressor must always be kept dry and must
not be left outdoors after work is complete.
8. Attachment and operation
m Important!
You must fully assemble the appliance before
using it for the first time!
You will require the following tools for assembly and
installation:
• 2 open-ended wrenches size 24 and 22 mm (not
supplied)
8.1 Fitting the wheels (fig. 6, 7)
• Screw a washer (C) on to the hex bolt (A) and pass
it through the enclosed wheel (3).
• Push a sleeve (D) onto the shaft and push it
through the wheel holder at the bottom of the pres-
sure vessel.
• Screw 1 washer and 1 nut each on to the threaded
wheels.
• Mount the wheels (3) on the wheel holders at the
bottom of the pressure vessel (2): To do this, use
a wrench to hold the hex bolt (A) at the wheel (3)
in place and tighten the washer (C) and the nut (B).
8.2 Fitting the supporting foot (fig. 5)
• Mount the enclosed supporting foot (4) using 2 hex
bolts (A), 4 washers (C) and 2 nuts (B), as shown
in figure 5.
8.3 Fitting the handle (fig. 8)
• Insert the 4 hexagon socket screws (F), each with
a washer, into the threaded holes on the right and
left of the transport handle (9) at the vessel.
• Secure the handle (9) with a washer (C) and a
nut (B).
8.4 Installing the air filter (10) (fig. 12 - 14)
• Remove the transport plug (fig. 12 pos. N).
• Attach the air filter (fig. 13/14) on the unit by turning
it clockwise (O) (fig. 14).
• For maintenance purposes, loosen the air filter by
turning it counter-clockwise (P) (fig. 14).
8.5 Fitting the compressed air hose
• A compressed air hose (not included in the scope
of supply*) can be used for work that takes place
at greater distances from the compressor. For this
purpose, connect the plug-in fitting of the com-
pressed air hose to one of the quick couplings (5).
Then connect the compressed air tool to the quick
coupling of the compressed air hose.
*Ask your compressor vendor, if you need com-
pressed air accessories for your device.
8.6 Changing the transportation cover (fig. 9 - 11)
• Remove the transport lid (12) of the oil filling open-
ing .
• Fill the included compressor oil into the crank hous-
ing and insert the included oil sealing plug into the
oil filling opening.
8.7 Checking the oil level (fig. 9 - 11)
Important!
For the first use, check the oil level of the com-
pressor. Operating the machine without oil will cause
irreparable damage and render the warranty invalid.
• Remove the plastic oil inlet plug on top of the crank
box of the compressor casing (fig. 9).
• Check the oil level in the sight glass (12). The
oil level should be in the centre of the red circle.
(fig. 11 pos. 12.1)
• Attach the supplied oil closing plug (11) and pull it
tight.
8.8 Mains connection
• The compressor is equipped with a mains cable
with shock-proof plug. This can be connected to
any 230 V~ / 50 Hz shock-proof socket which is
protected by a 8 A fuse.
• Before you use the machine, make sure that the
mains voltage is the same as the operating voltage
(see the rating plate).
• Long supply cables, extensions, cable reels etc.
cause a drop in voltage and can impede motor
start-up.
• At low temperatures below +5 °C, sluggishness
may make starting difficult or impossible.
GB | 23
Werbung
